- 您现在的位置：买卖IC网 > PDF目录98281 > TPS40074RHL (TEXAS INSTRUMENTS INC) 2 A SWITCHING CONTROLLER, 550 kHz SWITCHING FREQ-MAX, PQCC20 PDF资料下载
参数资料
| 型号： | TPS40074RHL |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 稳压器 |
| 英文描述： | 2 A SWITCHING CONTROLLER, 550 kHz SWITCHING FREQ-MAX, PQCC20 |
| 封装： | PLASTIC, QFN-20 |
| 文件页数： | 6/37页 |
| 文件大小： | 448K |
| 代理商： | TPS40074RHL |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页
www.ti.com
VDG03173
T2
T1
T3
T1
VSW
VIN 2V
IILIM
VILIM Threshold
(A)
(B)
TPS40074
SLUS617–APRIL 2005
APPLICATION INFORMATION (continued)
In addition, just prior to the high-side MOSFET turning on, the ILIM pin is pulled down to approximately half of
VDD. The ILIM pin is allowed to return to its nominal value after one of two events occur:
1. The SW node rises to within approximately 2 V of VDD
2. An internal timeout occurs, approximately 125-ns after ILIM is initially pulled down
If the SW node rises to within approximately 2-V of VDD, the device allows ILIM to go back to its nominal value.
This is illustrated in Figure 10 A. T1 is the delay time from the internal PWM signal being asserted and the rise of
SW. This includes the driver delay of 50 ns typical, and the turn on time of the high-side MOSFET. The MOSFET
used should have a turn on time less than 75 ns. T2 is the reaction time of the sensing circuit that allows ILIM to
start to return to its nominal value, typically 20ns.
The second event that can cause ILIM to return to its nominal value is for an internal timeout to expire. This is
illustrated in Figure 10 B as T3. Here SW never rises to VDD-2, for whatever reason, and the internal timer times
out. This allows the ILIM pin to start its transition back to its nominal value.
Prior to ILIM starting back to its nominal value, short circuit sensing is not enabled. In normal operation, this
insures that the SW node is at a higher voltage than ILIM when short circuit sensing starts, avoiding false trips
while allowing for a quicker blanking delay than would ordinarily be possible. Placing a capacitor across RILIM
sets an exponential approach to the normal voltage at the ILIM pin. This exponential “decay” of the short circuit
threshold can be used to compensate for ringing on the SW node after its rising edge and to help compensate
for slower turn-on MOSFETs. Choosing the proper capacitance requires care. If the capacitance is too large, the
voltage at ILIM does not approach the desired short circuit level quickly enough, resulting in an apparent shift in
short circuit threshold as pulse width changes.
The comparator that looks at ILIM and SW to determine if a short circuit condition exists has a clamp on its SW
input. This clamp makes the SW node never appear to fall more than 1.4 V (approximately, could be as much as
2 V at – 40°C) below VDD. While ILIM is more than 1.4 V below VDD short circuit sensing is effectively disabled,
giving a programmable absolute blanking time. As a general rule, it is best to make the time constant of the R-C
at the ILIM pin 20% or less of the nominal pulse width of the converter (See Equation 11)
Figure 10. Voltage Feed-Forward and PWM Duty Cycle Waveforms
The second tier protection incorporates a fault counter. The fault counter is incremented on each cycle with an
overcurrent pulse and decremented on a clock cycle without an overcurrent pulse. When the counter reaches
seven (7) a fault condition is declared by the controller. When this happens, the output drivers turn both
14
相关PDF资料 |
PDF描述 |
|---|---|
| TPS40075RHLR | 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PQCC20 |
| TPS40075RHLTG4 | 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PQCC20 |
| TPS40077PWPR | 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| TPS40077PWPRG4 | 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| TPS40077PWPG4 | 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS40074RHLR | 功能描述:DC/DC 开关控制器 Mid Input Sync Buck w/Vltg Feed-Fwd RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| TPS40074RHLRG4 | 功能描述:DC/DC 开关控制器 Mid Input Sync Buck w/Vltg Feed-Fwd RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| TPS40074RHLT | 功能描述:DC/DC 开关控制器 Mid Input Sync Buck w/Vltg Feed-Fwd RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| TPS40074RHLTG4 | 功能描述:DC/DC 开关控制器 Mid Input Sync Buck w/Vltg Feed-Fwd RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| TPS40075 | 制造商:TI 制造商全称:Texas Instruments 功能描述:4.5V TO 18V INPUT 10 PIN SYNCHRONOUS BUCK CONTROLLER WITH POWER GOOD |
发布紧急采购，3分钟左右您将得到回复。