- 您现在的位置：买卖IC网 > PDF目录69509 > TPS43000PWRG4 (TEXAS INSTRUMENTS INC) SWITCHING CONTROLLER, 2000 kHz SWITCHING FREQ-MAX, PDSO16 PDF资料下载
参数资料
| 型号： | TPS43000PWRG4 |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING CONTROLLER, 2000 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封装： | GREEN, TSSOP-16 |
| 文件页数： | 6/31页 |
| 文件大小： | 615K |
| 代理商： | TPS43000PWRG4 |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
TPS43000
SLUS489 OCTOBER 2001
14
www.ti.com
APPLICATION INFORMATION
error amplifier
The TPS43000 uses voltage mode control for each of the topologies. The output voltage is sensed and fed back
to the FB pin (inverting input) and compared to an internal 800 mV reference connected to the non-inverting
input. The difference (i.e. error voltage), is amplified by the internal error amplifier. The output of the error
amplifier (COMP), is then compared to the oscillator sawtooth ramp to control the pulse width used to drive the
power switch (energizing MOSFET). The duty cycle is varied to regulate the output voltage. The higher the error
voltage, the longer the energizing MOSFET switch is on.
The transient response of a converter is a function of both small signal and large signal responses. The small
signal response is determined by the error amplifier’s loop compensation (feedback network), whereas the large
signal response is a function of the error amplifier’s gain bandwidth and slew rate (dv/dt) as well as the slew
rate of the inductor current (di/dt). The TPS43000 internal error amplifier has a 5-MHz unity gain bandwidth. This
almost assures that the loop bandwidth is limited by external circuit characteristics rather than error amplifier
limitations. The internal error amplifier is capable of sourcing and sinking an ensured 500
A, which assures
that even during large signal transients, external components determine circuit behavior. Using low feedback
capacitance allows the error amplifier to rapidly slew from one level to another, insuring excellent transient
response.
loop compensation
The voltage loop needs to be compensated to provide control loop stability margin, and to minimize the output
voltage overshoot/undershoot response to line and load transients. A Type III error amplifier compensation
network can be used to optimize the loop response for any of the topologies and operating modes implemented
with the TPS43000. The Type III amplifier circuit is shown in Figure 2. This configuration has a pole at the origin
and two zero-pole pairs. It can provide up to 180
° of phase boost.
VOUT
C3
RBIAS
VREF
R3
R1
C1
R2
+
C2
Figure 2. Type III Error Amplifier Compensation
Network
0 dB
Av1
Av2
fz1
fz2
fp1
fp2
Gain
d
B
Figure 3. Type III Error Amplifier Compensation
Gain Response
t Time ns
相关PDF资料 |
PDF描述 |
|---|---|
| TPS5102IDBT | 3 A DUAL SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO30 |
| TPS5102IDBTG4 | 3 A DUAL SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO30 |
| TPS51116PWPR | 6 A SWITCHING CONTROLLER, PDSO20 |
| TPS51116RGER | 6 A SWITCHING CONTROLLER, PQCC24 |
| TPS51116PWPRG4 | 6 A SWITCHING CONTROLLER, PDSO20 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS43060 | 制造商:TI 制造商全称:Texas Instruments 功能描述:Low Quiescent Current Synchronous Boost DC-DC Controller with Wide VIN Range |
| TPS43060EVM-199 | 功能描述:电源管理IC开发工具 TPS43060 EVAL MOD RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| TPS43060RTER | 功能描述:DC/DC 开关控制器 Sync Boost Cntlr Wide Input Vtg RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| TPS43060RTET | 功能描述:DC/DC 开关控制器 Sync Boost Cntlr Wide Input Vtg RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| TPS43061EVM-198 | 功能描述:电源管理IC开发工具 TPS43061 EVAL MOD RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。