- 您现在的位置：买卖IC网 > PDF目录98282 > TPS54240QDGQRQ1 (TEXAS INSTRUMENTS INC) 2.5 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PDSO10 PDF资料下载
参数资料
| 型号： | TPS54240QDGQRQ1 |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 稳压器 |
| 英文描述： | 2.5 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PDSO10 |
| 封装： | GREEN, PLASTIC, MSOP-10 |
| 文件页数： | 4/48页 |
| 文件大小： | 1447K |
| 代理商： | TPS54240QDGQRQ1 |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
SLVSAQ4A
– DECEMBER 2010 – REVISED APRIL 2011
OVERVIEW
The TPS54240-Q1 device is a 42-V, 2.5-A, step-down (buck) regulator with an integrated high side n-channel
MOSFET. To improve performance during line and load transients the device implements a constant frequency,
current mode control which reduces output capacitance and simplifies external frequency compensation design.
The wide switching frequency of 100kHz to 2500kHz allows for efficiency and size optimization when selecting
the output filter components. The switching frequency is adjusted using a resistor to ground on the RT/CLK pin.
The device has an internal phase lock loop (PLL) on the RT/CLK pin that is used to synchronize the power
switch turn on to a falling edge of an external system clock.
The TPS54240-Q1 has a default start up voltage of approximately 2.5V. The EN pin has an internal pull-up
current source that can be used to adjust the input voltage under voltage lockout (UVLO) threshold with two
external resistors. In addition, the pull up current provides a default condition. When the EN pin is floating the
device will operate. The operating current is 138
μA when not switching and under no load. When the device is
disabled, the supply current is 1.3
μA.
The integrated 200m
high side MOSFET allows for high efficiency power supply designs capable of delivering
2.5 amperes of continuous current to a load. The TPS54240-Q1 reduces the external component count by
integrating the boot recharge diode. The bias voltage for the integrated high side MOSFET is supplied by a
capacitor on the BOOT to PH pin. The boot capacitor voltage is monitored by an UVLO circuit and will turn the
high side MOSFET off when the boot voltage falls below a preset threshold. The TPS54240-Q1 can operate at
high duty cycles because of the boot UVLO. The output voltage can be stepped down to as low as the 0.8V
reference.
The TPS54240-Q1 has a power good comparator (PWRGD) which asserts when the regulated output voltage is
less than 92% or greater than 109% of the nominal output voltage. The PWRGD pin is an open drain output
which deasserts when the VSENSE pin voltage is between 94% and 107% of the nominal output voltage
allowing the pin to transition high when a pull-up resistor is used.
The TPS54240-Q1 minimizes excessive output overvoltage (OV) transients by taking advantage of the OV power
good comparator. When the OV comparator is activated, the high side MOSFET is turned off and masked from
turning on until the output voltage is lower than 107%.
The SS/TR (slow start/tracking) pin is used to minimize inrush currents or provide power supply sequencing
during power up. A small value capacitor should be coupled to the pin to adjust the slow start time. A resistor
divider can be coupled to the pin for critical power supply sequencing requirements. The SS/TR pin is discharged
before the output powers up. This discharging ensures a repeatable restart after an over-temperature fault,
UVLO fault or a disabled condition.
The TPS54240-Q1, also, discharges the slow start capacitor during overload conditions with an overload
recovery circuit. The overload recovery circuit will slow start the output from the fault voltage to the nominal
regulation voltage once a fault condition is removed. A frequency foldback circuit reduces the switching
frequency during startup and overcurrent fault conditions to help control the inductor current.
12
Copyright
2010–2011, Texas Instruments Incorporated
相关PDF资料 |
PDF描述 |
|---|---|
| TPS54260DGQR | SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS54260QDGQRQ1 | 2.5 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS5430MDDAREPG4 | 8.5 A SWITCHING REGULATOR, 600 kHz SWITCHING FREQ-MAX, PDSO8 |
| TPS54310MPWPREP | 6 A SWITCHING REGULATOR, 775 kHz SWITCHING FREQ-MAX, PDSO20 |
| TPS54310PWPRG4 | 6 A SWITCHING REGULATOR, 762 kHz SWITCHING FREQ-MAX, PDSO20 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS54240QDRCRQ1 | 功能描述:Buck, Split Rail Switching Regulator IC Positive Adjustable 0.8V 1 Output 2.5A 10-VFDFN Exposed Pad 制造商:texas instruments 系列:汽车级，AEC-Q100，SWIFT?，Eco-Mode? 包装:剪切带（CT） 零件状态:有效 功能:降压 输出配置:正 拓扑:降压，分离轨 输出类型:可调式 输出数:1 电压 - 输入（最小值）:3.5V 电压 - 输入（最大值）:42V 电压 - 输出（最小值/固定）:0.8V 电压 - 输出（最大值）:39V 电流 - 输出:2.5A 频率 - 开关:100kHz ~ 2.5MHz 同步整流器:无 工作温度:-40°C ~ 125°C（TA） 安装类型:表面贴装 封装/外壳:10-VFDFN 裸露焊盘 供应商器件封装:10-VSON（3x3） 标准包装:1 |
| TPS54260 | 制造商:TI 制造商全称:Texas Instruments 功能描述:3.5V to 60V INPUT, 2.5A, STEP DOWN CONVERTER WITH ECO-MODE? |
| TPS54260_1 | 制造商:TI 制造商全称:Texas Instruments 功能描述:3.5V to 60V INPUT, 2.5A, STEP DOWN CONVERTER WITH ECO-MODE? |
| TPS54260_2 | 制造商:TI 制造商全称:Texas Instruments 功能描述:3.5V to 60V INPUT, 2.5A, STEP DOWN CONVERTER WITH ECO-MODE? |
| TPS54260DGQ | 功能描述:直流/直流开关调节器 3.5-60V 2.5A 2.5MHz Step Down Converter RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
发布紧急采购，3分钟左右您将得到回复。