- 您现在的位置：买卖IC网 > PDF目录98285 > TPS650531RGER (TEXAS INSTRUMENTS INC) 5-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC24 PDF资料下载
参数资料
| 型号： | TPS650531RGER |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 电源管理 |
| 英文描述： | 5-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC24 |
| 封装： | 4 X 4 MM, 0.50 MM PITCH, GREEN, PLASTIC, QFN-24 |
| 文件页数： | 6/27页 |
| 文件大小： | 858K |
| 代理商： | TPS650531RGER |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
100% Duty Cycle Low Dropout Operation
Vin
min + Voutmax ) Ioutmax
RDSonmax ) RL
(3)
Undervoltage Lockout
MODE SELECTION
ENABLE
RESET
SLVS754C – MARCH 2007 – REVISED SEPTEMBER 2009 ............................................................................................................................................. www.ti.com
The converters offer a low input to output voltage difference while still maintaining operation with the use of the
100% duty cycle mode. In this mode the P-channel switch is constantly turned on. This is particularly useful in
battery-powered applications to achieve longest operation time by taking full advantage of the whole battery
voltage range, i.e. The minimum input voltage to maintain regulation depends on the load current and output
voltage and can be calculated as:
with:
Ioutmax = maximum output current plus inductor ripple current
RDSonmax = maximum P-channel switch rDS(on)
RL = DC resistance of the inductor
Voutmax = nominal output voltage plus maximum output voltage tolerance
With decreasing load current, the device automatically switches into pulse skipping operation in which the power
stage operates intermittently based on load demand. By running cycles periodically the switching losses are
minimized and the device runs with a minimum quiescent current maintaining high efficiency.
In power save mode the converter only operates when the output voltage trips below its nominal output voltage.
It ramps up the output voltage with several pulses and goes again into power save mode once the output voltage
exceeds the nominal output voltage.
The undervoltage lockout circuit prevents the device from malfunctioning by disabling the converter at low input
voltages and from excessive discharge of the battery. The undervoltage lockout threshold is typically 1.8 V, max
2 V.
The MODE pin allows mode selection between forced PWM Mode and power Save Mode for both converters.
Connecting this pin to GND enables the automatic PWM and power save mode operation. The converters
operate in fixed frequency PWM mode at moderate to heavy loads and in the PFM mode during light loads,
maintaining high efficiency over a wide load current range.
Pulling the MODE pin high forces both converters to operate constantly in the PWM mode even at light load
currents. The advantage is the converters operate with a fixed frequency that allows simple filtering of the
switching frequency for noise sensitive applications. In this mode, the efficiency is lower compared to the power
save mode during light loads. For additional flexibility it is possible to switch from power save mode to forced
PWM mode during operation. This allows efficient power management by adjusting the operation of the converter
to the specific system requirements.
The devices have a separate enable pin for each of the dcdc converters and for each of the LDO to start up
independently. If EN_DCDC1, EN_DCDC2, EN_LDO1, EN_LDO2, EN_LDO3 are set to high, the corresponding
converter starts up with soft start as previously described.
Pulling the enable pin low forces the device into shutdown, with a shutdown quiescent current as defined in the
electrical characteristics. In this mode, the P and N-Channel MOSFETs are turned-off, the and the entire internal
control circuitry is switched-off. If disabled, the outputs of the LDOs are pulled low by internal 350
resistors,
actively discharging the output capacitor. For proper operation the enable pins must be terminated and must not
be left unconnected.
The TPS65053x contain circuitry that can generate a reset pulse for a processor with a 100ms delay time. The
input voltage at a comparator is sensed at an input called THRESHOLD. When the voltage exceeds the 1V
threshold, the output goes high after a 100ms delay time. This circuitry is functional as soon as the supply
voltage at Vcc exceeds the undervoltage lockout threshold. The RESET circuitry is active even if all DCDC
converters and LDOs are disabled.
14
Copyright 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65053 TPS650531 TPS650532
相关PDF资料 |
PDF描述 |
|---|---|
| TPS65055RSMR | 1.8 A DUAL SWITCHING CONTROLLER, 2475 kHz SWITCHING FREQ-MAX, PQCC32 |
| TPS65058RGET | 1.8 A DUAL SWITCHING CONTROLLER, 2475 kHz SWITCHING FREQ-MAX, PQCC32 |
| TPS650732TRSLRQ1 | POWER SUPPLY SUPPORT CKT, PQCC48 |
| TPS65110RGEG3 | SWITCHED CAPACITOR REGULATOR, 520 kHz SWITCHING FREQ-MAX, PQCC24 |
| TPS65130RGER | 0.9 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PQCC24 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS650531RGET | 功能描述:PMIC 解决方案 5Ch Pwr Mgmt IC w/2 Step-Down Converters RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| TPS650532RGER | 功能描述:PMIC 解决方案 5Ch Power Mgmt IC RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| TPS650532RGET | 功能描述:PMIC 解决方案 5Ch Power Mgmt IC RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| TPS65053EVM-217 | 功能描述:电源管理IC开发工具 TPS65053 Eval Mod RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| TPS65053EVM-389 | 功能描述:电源管理IC开发工具 TPS65053EVM-389 Eval Mod RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。