- 您现在的位置：买卖IC网 > PDF目录69522 > TPS65101PWP (TEXAS INSTRUMENTS INC) 2.6 A SWITCHING REGULATOR, 2100 kHz SWITCHING FREQ-MAX, PDSO24 PDF资料下载
参数资料
| 型号： | TPS65101PWP |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 稳压器 |
| 英文描述： | 2.6 A SWITCHING REGULATOR, 2100 kHz SWITCHING FREQ-MAX, PDSO24 |
| 封装： | GREEN, PLASTIC, HTSSOP-24 |
| 文件页数： | 7/30页 |
| 文件大小： | 1213K |
| 代理商： | TPS65101PWP |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
www.ti.com
Converter Loop Design and Stability
Design Procedure Quick Steps
Setting the Output Voltage and Selecting the Feedforward Capacitor
Vout + 1.146 V
1 )
R1
R2
R1
430 k
SW
FB1
SUP
C2+
C2/MODE
D1
C8
6.8 pF
C4
22
F
C2
0.22
F
R2
56 k
VO1
Up to 10 V/150 mA
z +
1
2
p
C8
R1
SLVS496C – SEPTEMBER 2003 – REVISED APRIL 2006
The TPS6510x series converter loop can be externally compensated and allows access to the internal
transconductance error amplifier output at the COMP pin. A small feedforward capacitor across the upper
feedback resistor divider speeds up the circuit as well. To test the converter stability and load transient
performance of the converter, a load step from 50 mA to 250 mA is applied, and the output voltage of the
converter is monitored. Applying load steps to the converter output is a good tool to judge the stability of such a
boost converter.
1. Select the feedback resistor divider to set the output voltage.
2. Select the feedforward capacitor to place a zero at 50 kHz.
3. Select the compensation capacitor on pin COMP. The smaller the value, the higher the low frequency gain.
4. Use a 50-k
potentiometer in series to C
c and monitor Vout during load transients. Fine tune the load
transient by adjusting the potentiometer. Select a resistor value that comes closest to the potentiometer
resistor value. This needs to be done at the highest V
in and highest load current since the stability is most
critical at these conditions.
The output voltage is set by the external resistor divider and is calculated as:
Across the upper resistor a bypass capacitor is required to speed up the circuit during load transients as shown
in Figure 15.
Figure 15. Feedforward Capacitor
Together with R1 the bypass capacitor C8 sets a zero in the control loop at approximately 50 kHz:
A value closest to the calculated value should be used. Larger feedforward capacitor values reduce the load
regulation of the converter and cause load steps as shown in Figure 16.
15
相关PDF资料 |
PDF描述 |
|---|---|
| TPS65120RGTR | 0.2 A SWITCHING REGULATOR, 4000 kHz SWITCHING FREQ-MAX, PQCC16 |
| TPS65120RGTTG4 | 0.2 A SWITCHING REGULATOR, 4000 kHz SWITCHING FREQ-MAX, PQCC16 |
| TPS65121RGT | 0.2 A SWITCHING REGULATOR, 4000 kHz SWITCHING FREQ-MAX, PQCC16 |
| TPS65120RGTRG4 | 0.2 A SWITCHING REGULATOR, 4000 kHz SWITCHING FREQ-MAX, PQCC16 |
| TPS65121RGTR | 0.2 A SWITCHING REGULATOR, 4000 kHz SWITCHING FREQ-MAX, PQCC16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS65101PWPG4 | 功能描述:LCD 驱动器 Triple Output LCD Supply RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| TPS65101PWPR | 功能描述:LCD 驱动器 Triple Output LCD Supply RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| TPS65101PWPRG4 | 功能描述:LCD 驱动器 Triple Output LCD Supply RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| TPS65101RGER | 功能描述:LCD 驱动器 Triple Output LCD Supply RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| TPS65101RGERG4 | 功能描述:LCD 驱动器 Triple Output LCD Supply RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。