参数资料
型号: TPS65250RHAR
厂商: TEXAS INSTRUMENTS INC
元件分类: 稳压器
英文描述: 4 A SWITCHING REGULATOR, 2200 kHz SWITCHING FREQ-MAX, PQCC40
封装: 6 X 6 MM, GREEN, PLASTIC, MO-220VJJD-2, VQFN-40
文件页数: 10/38页
文件大小: 1782K
代理商: TPS65250RHAR
T ms
V
ss
REF
(
) =
( )
(C nF
ss(
)
-
I
A
ss(
)
0.8
2
1
0.8
O
V
R
V
=
×
÷
-
è
FB
0.8V
Vo
+
-
TPS65250
R1
R2
SLVSAA3B – JUNE 2010 – REVISED JANUARY 2011
www.ti.com
Out-of-Phase Operation
Buck 1 has a low conduction resistance compared to Buck 2 and 3. Normally buck 1 is used to drive higher
system loads. Buck 2 and 3 are used to drive some peripheral loads like I/O and line drivers . The combination of
buck 2 and 3’s loads may be on par with Buck 1’s. In order to reduce input ripple current, buck 2 operates in
phase with buck 3; buck 1 and buck 2 operate 180 degrees out-of-phase. This enables the system, having less
input ripple, to lower component cost, save board space and reduce EMI.
Delayed Start-Up
If a delayed start-up is required on any of the buck converters fit a ceramic capacitor to the ENx pins. The delay
added is ~1.67 ms per nF connected to the pin. Note that the EN pins have a weak 1-M
pull-up to the 3V3 rail.
Soft Start Time
The device has an internal pull-up current source of 5 A that charges an external slow start capacitor to
implement a slow start time. Equation 2 shows how to select a slow start capacitor based on an expected slow
start time. The voltage reference (VREF) is 0.8 V and the slow start charge current (Iss) is 5 A. The soft start
circuit requires 1 nF per 200 S to be connected at the SS pin. A 1-ms soft-start time is implemented for all
converters fitting 4.7 nF to the relevant pins.
(2)
Adjusting the Output Voltage
The output voltage is set with a resistor divider from the output node to the FB pin. It is recommended to use 1%
tolerance or better divider resistors. In order to improve efficiency at light load, start with 40.2 k
for the R1
resistor and use the Equation 3 to calculate R2.
(3)
Figure 31. Voltage Divider Circuit
Error Amplifier
The device has a transconductance error amplifier. The transconductance of the error amplifier is 130 A/V
during normal operation. The frequency compensation network is connected between the COMP pin and ground.
Loop Compensation
TPS65250 is a current mode control dc/dc converter. The error amplifier is a 130-A/V transconductance
amplifier. A type-II compensation circuit is adequate for the converter to have a phase margin between 60 and 90
degrees.
18
Copyright 2010–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS65250
相关PDF资料
PDF描述
TPSD336K020R0200 KONDENSATOR TANTAL SMD 33UF 20V
TPSD336K035R0300 KONDENSATOR TANTAL SMD 33UF 35V
TPSD476K016R0150 KONDENSATOR TANTAL SMD 47UF 16V
TPSD476K025R0250 KONDENSATOR TANTAL SMD 47UF 25V
TPSD686K016R0150 KONDENSATOR TANTAL SMD 68UF 16V
相关代理商/技术参数
参数描述
TPS65250RHAT 功能描述:PMIC 解决方案 PMU w/3 DC/DC Cnvrtr & Charge & Pump RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel
TPS652510EVM 功能描述:电源管理IC开发工具 TPS652510 Eval Mod RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
TPS652510RHAR 功能描述:PMIC 解决方案 3 DC-DC Converters RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel
TPS652510RHAT 功能描述:PMIC 解决方案 3 DC-DC Converters RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel
TPS65251-1RHAT 功能描述:Buck Switching Regulator IC Positive Adjustable 0.8V 3 Output 3A, 2A 40-VFQFN Exposed Pad 制造商:texas instruments 系列:- 包装:剪切带(CT) 零件状态:有效 功能:降压 输出配置:正 拓扑:降压 输出类型:可调式 输出数:3 电压 - 输入(最小值):4.5V 电压 - 输入(最大值):18V 电压 - 输出(最小值/固定):0.8V 电压 - 输出(最大值):17V 电流 - 输出:3A,2A 频率 - 开关:300kHz ~ 2.2MHz 同步整流器:是 工作温度:-40°C ~ 125°C (TJ) 安装类型:表面贴装 封装/外壳:40-VFQFN 裸露焊盘 供应商器件封装:40-VQFN(6x6) 标准包装:1