参数资料
型号: TS34118CS
厂商: Taiwan Semiconductor Co., Ltd.
英文描述: Voice Switched Speakerphone Circuit
中文描述: 语音开关扬声器电路
文件页数: 7/20页
文件大小: 328K
代理商: TS34118CS
TS34118
7-20
2004/09 rev. B
Introduction
The fundamental difference between the operation of a speakerphone and a handset is that of half-duplex versus full
duplex. The handset is full duplex since con-version can occur in both directions (transmit and receive) simultaneously.
A speakerphone has higher gain levels in both paths and attempting to converse full duplex results in oscillatory
problems due to the loop that exists within the system. The loop is formed by the receive and transmit paths, the hybrid,
and the acoustic coupling (speaker to microphone). The only practical and economical solution used to data is to design
the speakerphone to function in a half duplex mode – i.e. only one person speaks at a time, while the other listens. To
achieve this required a circuit which can detect who is talking, switch on the appropriate path (transmit or receive) and
switch off (attenuate) the other path. In this way, the loop gain is maintained less than unity. When the talkers exchange
function, the circuit must quickly detect this, and switch the circuit appropriately. By providing speech level detectors the
circuit operates in a “hands free” mode, eliminating the need for a “push to talk” switch.
The handset by the way, has the same loop as the speakerphone. But since the gains are considerably lower, and
since the acoustic compiling from the earpiece to the mouthpiece is almost non existent (the receiver is normally held
against a person’s eat.) oscillations don’t occur.
The TS341118 provides the necessary level detectors, attenuators, and switching control for a properly operating
speakerphone. The detection sensitivity and timing are externally controllable. Additionally, the TS34118 provides
background nodule monitor’s which make the circuit insensitive to room and line noise, hybrid amplifier, and other
associated functions, please refer to the Block Diagram (Figure 2) when reading the following sections.
Attenuators
The transmit and receive attenuators are complementary in function. i .e. when one is at maximum gain (+6.0dB), the
other is at maximum attenuation (-4.5dB), and vice verse. They sum of their gains remains constant (within a nominal
error hand of ±0.1dB) at a typical value of ~40dB (see Figure 10). Their purpose is to control the transmit and receive
paths to provide the half-duplex operation required in a speakerphone.
The attenuators are non-inverting, and have a –3.0dB (from max gain) frequency of 100KHz. The input impedance of
each attenuator (TXI and RXI) is nominally 10K
(see Figure 3), and the input signal should be limited to 350mVrms
(990mVp-p) to prevent distortion. That maximum recommended input signal is independent of the volume control
setting. The diode clamp on the inputs the input swing, and therefore the maximum negative output swing. This is the
reason for V
RXOL
and VT
XOL
specification being defined as they are in the Electrical Characteristics. The output
impedance is 10
until the output current limit typically 2.5mA) is reached.
Figure 3. Attenuator Input Stage
相关PDF资料
PDF描述
TS34119 Low Power Audio Amplifier
TS34119CD Low Power Audio Amplifier
TS34119CS Low Power Audio Amplifier
TS34119CA COAXIAL T CNNCTRS NON-BH BNC AUTO T-CNNCTR F-M-F
TS3431AILT 1.24V programmable shunt voltage reference
相关代理商/技术参数
参数描述
TS34118CS28 功能描述:电信语音调制 IC Voice Switch Speaker phone Circuit RoHS:否 制造商:Epson Electronics America 产品: 应用:Voice Guidance product 封装 / 箱体:PQFP-52 电源电压-最大:3.6 V, 5.5 V 最大工作温度: 最小工作温度: 封装:
TS34118CS28 C8 制造商:SKMI/Taiwan 功能描述:Voice Switched Speakerphone Circuit 28-Pin SOP Tube
TS34118CS28C8 制造商:TSC 制造商全称:Taiwan Semiconductor Company, Ltd 功能描述:Voice Switched Speakerphone Circuit
TS34119 制造商:TSC 制造商全称:Taiwan Semiconductor Company, Ltd 功能描述:Low Power Audio Amplifier
TS34119_07 制造商:TSC 制造商全称:Taiwan Semiconductor Company, Ltd 功能描述:Low Power Audio Amplifier