- 您现在的位置：买卖IC网 > PDF目录297616 > TS83C51RD2ZZZ-VIA (ATMEL CORP) 8-BIT, MROM, 40 MHz, MICROCONTROLLER, PDIP40 PDF资料下载
参数资料
| 型号： | TS83C51RD2ZZZ-VIA |
| 厂商： | ATMEL CORP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, MROM, 40 MHz, MICROCONTROLLER, PDIP40 |
| 封装： | PLASTIC, DIP-40 |
| 文件页数： | 54/72页 |
| 文件大小： | 698K |
| 代理商： | TS83C51RD2ZZZ-VIA |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页当前第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页
58
Rev. B - Aug. 24, 1999
TS80C51RA2/RD2
TS83C51RB2/RC2/RD2
TS87C51RB2/RC2/RD2
NOTES
1.
ICC under reset is measured with all output pins disconnected; XTAL1 driven with TCLCH, TCHCL = 5 ns (see Figure 24.), VIL = VSS + 0.5 V,
VIH = VCC - 0.5V; XTAL2 N.C.; EA = RST = Port 0 = VCC. ICC would be slightly higher if a crystal oscillator used..
2.
Idle ICC is measured with all output pins disconnected; XTAL1 driven with TCLCH,TCHCL = 5 ns, VIL =VSS + 0.5 V, VIH =VCC - 0.5 V; XTAL2
3.
Power Down ICC is measured with all output pins disconnected; EA = VSS, PORT 0 = VCC; XTAL2 NC.; RST = VSS (see Figure 23.).
4.
Capacitance loading on Ports 0 and 2 may cause spurious noise pulses to be superimposed on the VOLs of ALE and Ports 1 and 3. The noise is
due to external bus capacitance discharging into the Port 0 and Port 2 pins when these pins make 1 to 0 transitions during bus operation. In the worst
cases (capacitive loading 100pF), the noise pulse on the ALE line may exceed 0.45V with maxi VOL peak 0.6V. A Schmitt Trigger use is not necessary.
5.
Typicals are based on a limited number of samples and are not guaranteed. The values listed are at room temperature and 5V.
6.
Under steady state (non-transient) conditions, IOL must be externally limited as follows:
Maximum IOL per port pin: 10 mA
Maximum IOL per 8-bit port:
Port 0: 26 mA
Ports 1, 2, 3 and 4 and 5 when available: 15 mA
Maximum total IOL for all output pins: 71 mA
If IOL exceeds the test condition, VOL may exceed the related specication. Pins are not guaranteed to sink current greater than the listed test conditions.
7.
For other values, please contact your sales ofce.
8.
Operating ICC is measured with all output pins disconnected; XTAL1 driven with TCLCH, TCHCL = 5 ns (see Figure 24.), VIL = VSS + 0.5 V,
VIH =VCC - 0.5V; XTAL2 N.C.; EA = Port 0 = VCC; RST = VSS. The internal ROM runs the code 80 FE (label: SJMP label). ICC would be slightly
higher if a crystal oscillator is used. Measurements are made with OTP products when possible, which is the worst case.
Figure 20. ICC Test Condition, under reset
ICC
operating
Power Supply Current Maximum values, X1
mode: (7)
1 + 0.3 Freq
(MHz)
@12MHz 4.6
@16MHz 5.8
mA
VCC = 3.3 V
(8)
ICC
idle
Power Supply Current Maximum values, X1
mode: (7)
0.15 Freq
(MHz) + 0.2
@12MHz 2
@16MHz 2.6
mA
VCC = 3.3 V
(2)
Symbol
Parameter
Min
Typ
Max
Unit
Test Conditions
EA
VCC
ICC
(NC)
CLOCK
SIGNAL
VCC
All other pins are disconnected.
RST
XTAL2
XTAL1
VSS
VCC
P0
相关PDF资料 |
PDF描述 |
|---|---|
| TS87C51RD2-VCM | 8-BIT, OTPROM, 40 MHz, MICROCONTROLLER, PDIP40 |
| TS83C51RC2ZZZ-VCA | 8-BIT, MROM, 40 MHz, MICROCONTROLLER, PDIP40 |
| TSB100010US | 40 A, BARRIER STRIP TERMINAL BLOCK |
| TSB12LV01AIPZ | 1 CHANNEL(S), 400M bps, LOCAL AREA NETWORK CONTROLLER, PQFP100 |
| TSB150002 | 40 A, BARRIER STRIP TERMINAL BLOCK, 1 ROW, 1 DECK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TS83C51RD2ZZZ-VIAD | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Microcontroller |
| TS83C51RD2ZZZ-VIBB | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Microcontroller |
| TS83C51RD2ZZZ-VIBD | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Microcontroller |
| TS83C51RD2ZZZ-VIBR | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Microcontroller |
| TS83C51RD2ZZZ-VIEB | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Microcontroller |
发布紧急采购，3分钟左右您将得到回复。