- 您现在的位置：买卖IC网 > PDF目录199494 > TSPC106AMGSU66CE (ATMEL CORP) PCI BUS CONTROLLER, CBGA303 PDF资料下载
参数资料
| 型号： | TSPC106AMGSU66CE |
| 厂商： | ATMEL CORP |
| 元件分类： | 总线控制器 |
| 英文描述： | PCI BUS CONTROLLER, CBGA303 |
| 封装： | 21 X 25 MM, 3.84 MM HEIGHT, 1.27 MM PITCH, CICGA-303 |
| 文件页数： | 29/40页 |
| 文件大小： | 569K |
| 代理商： | TSPC106AMGSU66CE |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页当前第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
35
TSPC106
2102B–HIREL–02/02
Decoupling
Recommendations
Due to the TSPC106's large address and data buses, and high operating frequencies,
the TSPC106 can generate transient power surges and high frequency noise in its
power supply, especially while driving large capacitive loads. This noise must be pre-
vented from reaching other components in the system, and the TSPC106 itself requires
a clean, tightly regulated source of power.
It is strongly recommended that the system design include six to eight 0.1 F (ceramic)
and 10 F (tantalum) decoupling capacitors to provide both high- and low-frequency fil-
tering. These capacitors should be placed closely around the perimeter of the TSPC106
package (or on the underside of the PCB). It is also recommended that these decou-
pling capacitors receive their power from separate V
DD and GND power planes in the
PCB, utilizing short traces to minimize inductance. Only SMT (surface mount technol-
ogy) capacitors should be used to minimize lead inductance.
In addition, it is recommended that there be several bulk storage capacitors distributed
around the PCB, feeding the V
DD plane, to enable quick recharging of the smaller chip
capacitors. These bulk capacitors should have a low ESR (equivalent series resistance)
rating to ensure the quick response time necessary. They should also be connected to
the power and ground planes through two vias to minimize inductance. Suggested bulk
capacitors are 100 F (AVX TPS tantalum) or 330 F (AVX TPS tantalum).
Connection
Recommendations
To ensure reliable operation, it is recommended to connect unused inputs to an appro-
priate signal level. Unused active low inputs should be tied (using pull-up resistors) to
V
DD. Unused active high inputs should be tied (using pull-down resistors) to GND. All
NC (no-connect) signals must remain unconnected.
Power and ground connections must be made to all external V
DD,AVDD and GND pins
of the TSPC106.
Pull-up Resistor
Recommendations
The TSPC106 requires pull-up (or pull-down) resistors on several control signals of the
60x and PCI buses to maintain the control signals in the negated state after they have
been actively negated and released by the TSPC106 or other bus masters. The JTAG
test reset signal, TRST, should be pulled down during normal system operation. Also, as
indicated in Table 21, the factory test signal, LSSD_MODE, must bepulledupfor nor-
mal device operation.
During inactive periods on the bus, the address and transfer attributes on the bus
(A[0:31], TT[0:4], TBST,WT,CI and GBL) are not driven by any master and may float in
the high-impedance state for relatively long periods of time. Since the TSPC106 must
continually monitor these signals, this float condition may cause excessive power draw
by the input receivers on the TSPC106 or by other receivers in the system. It is recom-
mended that these signals be pulled up or restored in some manner by the system.
The 60x data bus input receivers on the TSPC106 do not require pull-up resistors on the
data bus signals (DH[0:31], DL[0:31] and PAR[0:7]). However, other data bus receivers
in the system may require pull-up resistors on these signals.
In general, the 60x address and control signals are pulled up to 3.3 Vdc and the PCI
control signals are pulled up to 5 Vdc through weak (2 - 10 k
) resistors. Resistor val-
ues may need to be adjusted stronger to reduce induced noise on specific board
designs. Table 21 summarizes the pull-up/pull-down recommendations for the
TSPC106.
相关PDF资料 |
PDF描述 |
|---|---|
| TSPC106AMGU83CE | PCI BUS CONTROLLER, CBGA303 |
| TSPC106AMGU/T83CG | PCI BUS CONTROLLER, CBGA303 |
| TSPC106AVG83CG | PCI BUS CONTROLLER, CBGA303 |
| TSPC106AVGS66CG | PCI BUS CONTROLLER, CBGA303 |
| TSPC106AMGSU66CG | PCI BUS CONTROLLER, CBGA303 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TSPC106AVG | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:PCI Bus Bridge Memory Controller 66-83 MHz |
| TSPC106AVG66CE | 制造商:未知厂家 制造商全称:未知厂家 功能描述:MEMORY CONTROLLER |
| TSPC106AVG66CG | 制造商:未知厂家 制造商全称:未知厂家 功能描述:MEMORY CONTROLLER |
| TSPC106AVG83CE | 制造商:未知厂家 制造商全称:未知厂家 功能描述:MEMORY CONTROLLER |
| TSPC106AVG83CG | 制造商:未知厂家 制造商全称:未知厂家 功能描述:MEMORY CONTROLLER |
发布紧急采购，3分钟左右您将得到回复。