参数资料
型号: TSPC603RVGSB/Q14LC
厂商: ATMEL CORP
元件分类: 微控制器/微处理器
英文描述: 32-BIT, 300 MHz, RISC PROCESSOR, CBGA255
封装: 21 X 21 MM, 3.84 MM HEIGHT, 1.27 MM PITCH, CERAMIC, CI-CGA-255
文件页数: 26/132页
文件大小: 10886K
代理商: TSPC603RVGSB/Q14LC
195
ATmega8535(L)
2502K–AVR–10/06
To initiate the Slave Receiver mode, TWAR and TWCR must be initialized as follows:
The upper seven bits are the address to which the Two-wire Serial Interface will respond
when addressed by a Master. If the LSB is set, the TWI will respond to the general call
address (0x00), otherwise it will ignore the general call address.
TWEN must be written to one to enable the TWI. The TWEA bit must be written to one
to enable the acknowledgement of the device’s own slave address or the general call
address. TWSTA and TWSTO must be written to zero.
When TWAR and TWCR have been initialized, the TWI waits until it is addressed by its
own slave address (or the general call address if enabled) followed by the data direction
bit. If the direction bit is “0” (write), the TWI will operate in SR mode, otherwise ST mode
is entered. After its own slave address and the write bit have been received, the TWINT
Flag is set and a valid status code can be read from TWSR. The status code is used to
determine the appropriate software action. The appropriate action to be taken for each
status code is detailed in Table 77. The Slave Receiver mode may also be entered if
arbitration is lost while the TWI is in the Master mode (see states 0x68 and 0x78).
If the TWEA bit is reset during a transfer, the TWI will return a “Not Acknowledge” (“1”)
to SDA after the next received data byte. This can be used to indicate that the Slave is
not able to receive any more bytes. While TWEA is zero, the TWI does not acknowledge
its own slave address. However, the Two-wire Serial Bus is still monitored and address
recognition may resume at any time by setting TWEA. This implies that the TWEA bit
may be used to temporarily isolate the TWI from the Two-wire Serial Bus.
In all sleep modes other than Idle mode, the clock system to the TWI is turned off. If the
TWEA bit is set, the interface can still acknowledge its own slave address or the general
call address by using the Two-wire Serial Bus clock as a clock source. The part will then
wake up from sleep and the TWI will hold the SCL clock low during the wake up and
until the TWINT Flag is cleared (by writing it to one). Further data reception will be car-
ried out as normal, with the AVR clocks running as normal. Observe that if the AVR is
set up with a long start-up time, the SCL line may be held low for a long time, blocking
other data transmissions.
Note that the Two-wire Serial Interface Data Register – TWDR – does not reflect the last
byte present on the bus when waking up from these sleep modes.
TWAR
TWA6
TWA5
TWA4
TWA3
TWA2
TWA1
TWA0
TWGCE
Value
Device’s Own Slave Address
TWCR
TWINT
TWEA
TWSTA
TWSTO
TWWC
TWEN
TWIE
Value
0
100
01
0
X
相关PDF资料
PDF描述
TSXPC603RVGB/Q14LC 32-BIT, 300 MHz, RISC PROCESSOR, CBGA255
TS80C31X2-LJER 8-BIT, 30 MHz, MICROCONTROLLER, PQFP44
TS80C32X2-ELCR 8-BIT, MICROCONTROLLER, PQFP44
TS80C31X2-VJBB 8-BIT, 40 MHz, MICROCONTROLLER, PQCC44
TSC80C31-16KAD 8-BIT, 16 MHz, MICROCONTROLLER, PDIP40
相关代理商/技术参数
参数描述
TSPC603RVGSU/T10LC 制造商:未知厂家 制造商全称:未知厂家 功能描述:MICROPROCESSOR|32-BIT|CMOS|BGA|255PIN|CERAMIC
TSPC603RVGSU/T12LC 制造商:未知厂家 制造商全称:未知厂家 功能描述:MICROPROCESSOR|32-BIT|CMOS|BGA|255PIN|CERAMIC
TSPC603RVGSU/T14LC 制造商:未知厂家 制造商全称:未知厂家 功能描述:MICROPROCESSOR|32-BIT|CMOS|BGA|255PIN|CERAMIC
TSPC603RVGSU/T6LC 制造商:未知厂家 制造商全称:未知厂家 功能描述:MICROPROCESSOR|32-BIT|CMOS|BGA|255PIN|CERAMIC
TSPC603RVGSU/T8LC 制造商:未知厂家 制造商全称:未知厂家 功能描述:MICROPROCESSOR|32-BIT|CMOS|BGA|255PIN|CERAMIC