- 您现在的位置：买卖IC网 > PDF目录373745 > TSS463C (Atmel Corp.) VAN Data Link Controller with Serial Interface PDF资料下载
参数资料
| 型号： | TSS463C |
| 厂商： | Atmel Corp. |
| 英文描述： | VAN Data Link Controller with Serial Interface |
| 中文描述： | 凡数据与串行接口链路控制器 |
| 文件页数： | 30/59页 |
| 文件大小： | 492K |
| 代理商： | TSS463C |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页当前第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页
30
TSS463C
7601B–AUTO–02/06
ETIP: Enable Transmission In
Progress
The Transmission In Progress (TIP) tells the diagnosis system to enable transmission
diagnosis.
One
: Enable TIP generation
Zero
: Disable TIP generation.
ESDC: Enable System
Diagnosis Clock
The Synchronous Diagnosis Clock (SDC) controls the cycle time of the synchronous
diagnosis.
One
: Enable SDC divider.
Zero
: Disable SDC divider.
Command Register (0x03)
Write only register.
Reserved: Bit 1, 2. These bits must not be set by the user; a zero must always be
written to these bit.
If the circuit is operating at low bitrates, there might be a considerable delay
between the writing of this register and the performing of the actual command (worst
case 6 timeslots). The user is therefore recommended to verify, by reading the Line
Status Register (0x04), that the commands have been performed.
GRES: General Reset
The Reset circuit command bit performs, if set, exactly as if the external reset pin was
asserted. This command bit has its own auto-reset circuitry.
One
: Reset active
Zero
: Reset inactive
SLEEP: Sleep command
(Section “Sleep Command”, page 51). If the user sets the Sleep bit, the circuit will enter
sleep mode. When the circuit is in sleep mode, all non-user registers are setup to mini-
mize power consumption. Read/write accesses to the TSS463C via the SPI/SCI
interface are impossible, the oscillator is stopped.
To exit from this mode the user must apply either an hardware reset (external RESET
pin) either an asynchronous software reset (via the SPI/SCI interface).
One:
Sleep active
Zero:
Sleep inactive
IDLE: Idle command
(Section “Idle and Activate Commands”, page 51). If the user sets the Idle bit, the circuit
will enter idle mode. In idle mode the oscillator will operate, but the TSS463C will not
transmit or receive anything on the bus, and the TxD output will be in tri-state
One
: Idle active
Zero
: Idle inactive
ACTI: Activate command
(Section “Idle and Activate Commands”, page 51). The Activate command will put the
circuit in the active mode, i.e it will transmit and receive normally on the bus. When the
circuit is in activate mode the TxD tri-state output is enabled.
One
: Activate active
Zero
: Activate inactive
7
6
5
4
3
2
1
0
GRES
SLEEP
IDLE
ACTI
REAR
0
0
MSDC
相关PDF资料 |
PDF描述 |
|---|---|
| TSS4B02G | Single Phase 4.0 Amps. Glass Passivated Super Fast Bridge Rectifiers |
| TSS4B03G | Single Phase 4.0 Amps. Glass Passivated Super Fast Bridge Rectifiers |
| TSS4B01G | Single Phase 4.0 Amps. Glass Passivated Super Fast Bridge Rectifiers |
| TSS5G45S | TOSHIBA SOLID STATE AC RELAY |
| TSS5J45S | TOSHIBA SOLID STATE AC RELAY |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TSS463C-TERA-9 | 功能描述:网络控制器与处理器 IC ASICS RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| TSS463C-TERZ-9 | 制造商:Atmel Corporation 功能描述: |
| TSS463C-TESZ-9 | 功能描述:网络控制器与处理器 IC ASICS RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| TSS463D | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Industrial Control IC |
| TSS463R | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Industrial Control IC |
发布紧急采购，3分钟左右您将得到回复。