- 您现在的位置：买卖IC网 > PDF目录373745 > TSS463C (Atmel Corp.) VAN Data Link Controller with Serial Interface PDF资料下载
参数资料
| 型号： | TSS463C |
| 厂商： | Atmel Corp. |
| 英文描述： | VAN Data Link Controller with Serial Interface |
| 中文描述： | 凡数据与串行接口链路控制器 |
| 文件页数： | 51/59页 |
| 文件大小： | 492K |
| 代理商： | TSS463C |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页当前第51页第52页第53页第54页第55页第56页第57页第58页第59页
51
TSS463C
7601B–AUTO–02/06
Activate, Idle and
Sleep Modes
Sleep, idle and activate commands are located in the Command Register (0x03). These
three commands are general commands for the TSS463C.
Idle and Activate
Commands
After reset, the TSS463C starts in idle mode. In this mode, the oscillator operates
(CKOUT pin active) but the circuit cannot transmit or receive anything on the VAN bus.
The TxD output (pin 12) is in tri-state mode, a pull-up resistor must be provided exter-
nally or by the line driver to avoid floating state on the VAN bus. To activate the
TSS463C, the user must set the activate bit (ACTI) and reset the idle bit (IDLE).
Figure 35.
Idle and Activate Timings
In both cases, the idle state can be verified reading the Line Status register (0x04).
Sleep Command
If the user sets the sleep bit (SLEEP), the TSS463C enters in sleep mode, regardless of
the values of activate and idle bits. It means that, all non-user registers are set-up to
reduce the power consumption and the internal oscillator is immediately stopped. Then,
accesses to all registers (and to the messages) via the SPI/SCI interface are impossible
and CKOUT is not provided.
To exit from this mode the user must apply either an hardware reset (external reset pin)
either an asynchronous software reset (via the SPI/SCI interface).
In a typical application (see Figure 5), using the CKOUT feature (pin 8), if the TSS463C
is put in sleep mode, the clock provided to the microcontroller is stopped. So, the system
does not run and the only way to awake this application is an external reset.
(max)
RxD
TxD
After Reset
Idle Mode
Activate Mode
Activate command
3 TS
8 TS
12 TS
TS: Timeslot Period
SOF
SOF
Idle Command
FCS
E
A
5 TS
4 TS
RxD
INT
Idle Mode
Activate Mode
相关PDF资料 |
PDF描述 |
|---|---|
| TSS4B02G | Single Phase 4.0 Amps. Glass Passivated Super Fast Bridge Rectifiers |
| TSS4B03G | Single Phase 4.0 Amps. Glass Passivated Super Fast Bridge Rectifiers |
| TSS4B01G | Single Phase 4.0 Amps. Glass Passivated Super Fast Bridge Rectifiers |
| TSS5G45S | TOSHIBA SOLID STATE AC RELAY |
| TSS5J45S | TOSHIBA SOLID STATE AC RELAY |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TSS463C-TERA-9 | 功能描述:网络控制器与处理器 IC ASICS RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| TSS463C-TERZ-9 | 制造商:Atmel Corporation 功能描述: |
| TSS463C-TESZ-9 | 功能描述:网络控制器与处理器 IC ASICS RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| TSS463D | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Industrial Control IC |
| TSS463R | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Industrial Control IC |
发布紧急采购，3分钟左右您将得到回复。