- 您现在的位置：买卖IC网 > PDF目录18804 > TXM-869-ES_ (Linx Technologies Inc)XMITTER RF 869MHZ 10PIN SMD PDF资料下载
参数资料
| 型号： | TXM-869-ES_ |
| 厂商： | Linx Technologies Inc |
| 文件页数： | 5/11页 |
| 文件大小： | 0K |
| 描述： | XMITTER RF 869MHZ 10PIN SMD |
| 产品变化通告： | ES Series Frequency Change 22/Dec/2010 |
| 标准包装： | 40 |
| 系列： | ES |
| 频率： | 869MHz |
| 应用： | 住宅/楼宇自动化，工业控制和监控 |
| 调制或协议： | AM，OOK |
| 数据传输率 - 最大： | 56 kbps |
| 功率 - 输出： | 4dBm |
| 电流 - 传输： | 8.5mA |
| 数据接口： | PCB，表面贴装 |
| 天线连接器： | PCB，表面贴装 |
| 电源电压： | 2.1 V ~ 4 V |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 模块 |
| 包装： | 散装 |
| 其它名称： | TXM-869-ES TXM-869-ES_-ND |
PROTOCOL GUIDELINES
While many RF solutions impose data formatting and balancing requirements,
Linx RF modules do not encode or packetize the signal content in any manner.
The received signal will be affected by such factors as noise, edge jitter, and
interference, but it is not purposefully manipulated or altered by the modules.
This gives the designer tremendous flexibility for protocol design and interface.
Despite this transparency and ease of use, it must be recognized that there are
distinct differences between a wired and a wireless environment. Issues such as
interference and contention must be understood and allowed for in the design
process. To learn more about protocol considerations, we suggest you read Linx
Application Note AN-00160.
Errors from interference or changing signal conditions can cause corruption of
the data packet, so it is generally wise to structure the data being sent into small
packets. This allows errors to be managed without affecting large amounts of
data. A simple checksum or CRC could be used for basic error detection. Once
an error is detected, the protocol designer may wish to simply discard the corrupt
data or implement a more sophisticated scheme to correct it.
INTERFERENCE CONSIDERATIONS
TYPICAL APPLICATIONS
USING THE ES SERIES TRANSMITTER FOR ANALOG APPLICATIONS
The ES Series is an excellent choice for sending analog information, including
audio. The ability of the ES to transmit combinations of analog and digital content
opens many new opportunities for design creativity.
Simple or complex analog signals within the specified audio bandwidth and input
levels may be connected directly to the transmitter’s DATA line. The transmitter
input is high impedance (500k Ω ) and can be directly driven by a wide variety of
sources, ranging from a single frequency to complex content, such as audio.
Analog sources should provide 0V to no more than 5V P-P maximum waveform
and should be AC-coupled into the DATA line. The size of the coupling capacitor
should be large enough to ensure the passage of all desired frequencies. Since
the modulation voltage applied to the DATA line determines the carrier deviation,
distortion can occur if the DATA line is over-driven. The actual level of the input
waveform should be adjusted to achieve optimum in-circuit results.
The RF spectrum is crowded and the potential for conflict with other unwanted
sources of RF is very real. While all RF products are at risk from interference, its
1
2
PDN
LADJ
ANT
GND
10
9
effects can be minimized by better understanding its characteristics.
3
VCC LO_V_D
8
Interference may come from internal or external sources. The first step is to
eliminate interference from noise sources on the board. This means paying
careful attention to layout, grounding, filtering, and bypassing in order to
0-Vcc Audio Source
4
5
GND
DATA
/CLK SE
/CLK
7
6
eliminate all radiated and conducted interference paths. For many products, this
is straightforward; however, products containing components such as switching
power supplies, motors, crystals, and other potential sources of noise must be
approached with care. Comparing your own design with a Linx evaluation board
can help to determine if and at what level design-specific interference is present.
External interference can manifest itself in a variety of ways. Low-level
interference will produce noise and hashing on the output and reduce the link’s
overall range.
High-level interference is caused by nearby products sharing the same
frequency or from near-band high-power devices. It can even come from your
own products if more than one transmitter is active in the same area. It is
important to remember that only one transmitter at a time can occupy a
frequency, regardless of the coding of the transmitted signal. This type of
interference is less common than those mentioned previously, but in severe
cases it can prevent all useful function of the affected device.
Although technically it is not interference, multipath is also a factor to be
understood. Multipath is a term used to refer to the signal cancellation effects
that occur when RF waves arrive at the receiver in different phase relationships.
This effect is a particularly significant factor in interior environments where
objects provide many different signal reflection paths. Multipath cancellation
results in lowered signal levels at the receiver and, thus, shorter useful distances
for the link.
Page 8
0.1μF
Figure 10: AC Coupling An Audio Source
USING THE ES SERIES TRANSMITTER FOR DIGITAL APPLICATIONS
The ES Series transmitter is equally capable at accommodating digital data. The
transmitter input is high impedance (500k) and can be directly driven by a wide
variety of sources including microprocessors and encoder ICs.
When the transmitter will be used to transmit digital data, the DATA line is best
driven from a 3 to 5V source. The transmitter is designed to give an average
deviation of 115kHz with a 5V square wave input, and 75kHz with 3V square
wave input. Either choice will achieve maximum performance.
Data adhering to different electrical level standards, such as RS-232, will require
buffering or conversion to logic level voltages. In the case of RS-232, such
buffering is easily handled with widely available ICs, such as the MAX232, which
is used on the ES Series Master Development System. The Linx SDM-USB-QS
can be used to convert between USB compliant signals and logic level voltages.
Page 9
相关PDF资料 |
PDF描述 |
|---|---|
| 14A-10R-20 | XFRMR PWR 115/230V 10V 1.0A |
| TXE-315-KH2 | TRANSMITTER RF 315MHZ SMT |
| 14A-10R-28 | XFRMR PWR 115/230V 14V .72A |
| MAX2903ETI+ | IC TX 868MHZ 200MW 28TQFN |
| 9922-18RED | LEAD PLUG STK BAN 2MM RED 18" |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TXM-869-ES_ | 功能描述:XMITTER RF 869MHZ 10PIN SMD RoHS:是 类别:RF/IF 和 RFID >> RF 发射器 系列:ES 标准包装:4,000 系列:- 频率:310MHz ~ 440MHz 应用:- 调制或协议:UHF，ASK 数据传输率 - 最大:20 kBaud 功率 - 输出:1dBm ~ 5dBm 电流 - 传输:10mA 数据接口:PCB，表面贴装 天线连接器:PCB，表面贴装 存储容量:- 特点:- 电源电压:2.2 V ~ 4 V 工作温度:-40°C ~ 85°C 封装/外壳:16-LSSOP（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| TXM-900-HP3-PPO | 功能描述:射频模块 RF Transmitter 900MHz 8-CH SIP Pack RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm |
| TXM-900-HP3-PPO_ | 功能描述:TRANSMITTER RF 900MHZ 8-CHANNEL RoHS:是 类别:RF/IF 和 RFID >> RF 发射器 系列:HP3 标准包装:4,000 系列:- 频率:310MHz ~ 440MHz 应用:- 调制或协议:UHF，ASK 数据传输率 - 最大:20 kBaud 功率 - 输出:1dBm ~ 5dBm 电流 - 传输:10mA 数据接口:PCB，表面贴装 天线连接器:PCB，表面贴装 存储容量:- 特点:- 电源电压:2.2 V ~ 4 V 工作温度:-40°C ~ 85°C 封装/外壳:16-LSSOP（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| TXM-900-HP3-PPS | 功能描述:射频模块 RF Transmitter900MHz 8&100-CH SIP Pack RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm |
| TXM-900-HP3-PPS_ | 制造商:Linx Technologies Inc 功能描述:TRANSMTR RF 900MHZ 8PAR/120SRLCH |
发布紧急采购，3分钟左右您将得到回复。