- 您现在的位置：买卖IC网 > PDF目录69541 > TXS80ZD-NP2R2H (POWER-ONE INC) 1-OUTPUT 200 W DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | TXS80ZD-NP2R2H |
| 厂商： | POWER-ONE INC |
| 元件分类： | 电源模块 |
| 英文描述： | 1-OUTPUT 200 W DC-DC REG PWR SUPPLY MODULE |
| 封装： | 2.400 X 3.450 INCH, 0.500 INCH HEIGHT, 3/4 BRICK PACKAGE-14 |
| 文件页数： | 15/27页 |
| 文件大小： | 2635K |
| 代理商： | TXS80ZD-NP2R2H |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
Product Specification
TXS Series: 75…120 A DC-DC Converters
36 to 75 V DC Input, 1.2, 1.5, 1.8, 2.0 and 2.5 V Output, 90 W to 250 W
REV. FEB 18, 2003
22 of 27
www.power-one.com
Radiated Noise
The radiated noise from the converter is extremely
difficult to predict since it depends largely upon the
motherboard
layout
and
the
switching
characteristic of the loads.
The report: “TXS layout considerations” on the
TXS product CD ROM provides recommendations
for reducing the radiated noise through shielding
and optimal layout.
Input Impedance
All switching power supplies exhibit negative input
impedance. A power source with inductive output
impedance and/or the wiring inductance from the
supply to the converter can affect the stability of
the modules.
A good general stability rule is, that the magnitude
of the source impedance should be lower than the
magnitude of the input impedance of the module at
all frequencies up to the switching frequency. The
minimum input impedance of a module is
calculated as 20 log(Ui min / Ii max).
Example: At Ui min = 36 V and Ii max = 7.8 A (see
Table 1 on page 3), a TXS100ZD needs an AC-
impedance
|Zline| < 13.2 dB at full load.
A possibility to reduce the input impedance is to
connect a low ESR input filter capacitor between
the input lines (at least 100 uF per 125 W output
power is recommended). With such a blocking
capacitor, a performance within the specifications
can be achieved with almost all supply conditions.
To consider:
- The stabilising input capacitor and the capacitors
of the input filters generate an inrush current.
- The blocking capacitor should be able to handle
the input ripple current of the module, which is
much larger than the reflected input ripple (see
measurement set up: figures 20/22).
- The capacitors may resonate with the inductance
of the input filter and the wiring. If this happens,
the resonance will require damping.
On Board Input and Output Filters
TXS converters use a topology that achieves input-
and output ripple frequencies four times higher
than the switching frequency. This results in
excellent ripple and noise values and low external
filter requirements.
The on board output filter is a parallel connection
of very low impedance Tantalum capacitors
connected in parallel with an overall capacitance of
3.3 mF. Total ESR < 4.5 m
(@100 kHz/25 °C).
The high efficient on-board input filter consists of
several ceramic capacitors, a damping network
and a filter inductor. Two EMC capacitors
(Cy1+Cy2) in a series connection with 2.2 nF
each, are connected between primary and
secondary.
Lin
C1
C2
TXS
pow er s t age
C3
1
2
5
6
Cy 1 + C y 2
Figure 52: On board input and output filters.
C1 =1uF, C2 =6 (1 uF), C3 =3 mF
Cy = 1.1 nF,
Lin = 0.9 uH
for
TXS
models ZC and ZD, 1.1 uH for models
ZY, ZA and ZB
Electromagnetic Susceptibility
The converter does not react to EMI pulses.
However the Y capacitors and the interwinding
capacitance of the multilayer board can couple
some common mode noise to the secondary.
Earthing or decoupling the output with large Y
capacitors needs a two stage EMC filter or a
ground line inductor to meet the EMC conducted
noise level B (see EMC specifications).
-
The EMI measurements have been done with
a one stage input filter according to Figure 44.
-
ESD pulses were directly discharged into the
TXS pins.
-
Burst pulses were applied in front of the input
filter.
Performance criterion A denotes normal operation,
no deviation from specification. Performance
criterion B denotes temporary deviation from
specification.
相关PDF资料 |
PDF描述 |
|---|---|
| W9725G6IB-18 | 16M X 16 DDR DRAM, 0.35 ns, PBGA84 |
| W9864G6EB-7 | 4M X 16 SYNCHRONOUS DRAM, 5.5 ns, PBGA60 |
| WE128K8200CQ | 128K X 8 EEPROM 5V MODULE, 200 ns, CDIP32 |
| WED9LC6816V1512BI | SPECIALTY MEMORY CIRCUIT, PBGA153 |
| WS128K32-35G2TMEA | 128K X 32 MULTI DEVICE SRAM MODULE, 35 ns, CQFP68 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TXS-86-515-S | 制造商:FLOYD BELL 功能描述:Alarm, Piezoelectric, 92 dBA to 103 dBA @ 2 Ft., Extra Loud Siren, 5-15VDC |
| TXS-86-515-SR | 制造商:FLOYD BELL 功能描述:Alarm, Piezoelectric, 92 dBA to 103 dBA @ 2 Ft., Extra Loud Siren, 5-15VDC |
| TX-SAW433S-Z-RFM | 制造商:AUREL 功能描述:RF MODULE TX OOK 434MHZ EXT ANT 制造商:AUREL 功能描述:RF MODULE, TX, OOK, 434MHZ, EXT ANT 制造商:AUREL 功能描述:RF MODULE, TX, OOK, 434MHZ, EXT ANT, Frequency:433.92MHz, Supply Voltage Min:4.5 |
| TX-SDK-V1/NOPB | 功能描述:数据转换 IC 开发工具 TX-SDK-V1 EVAL BRD RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
| TX-SDK-V2/NOPB | 功能描述:电源管理IC开发工具 Eval Brd fr Ultrasnd Transmit Solution RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。