- 您现在的位置：买卖IC网 > PDF目录21977 > UBA2014T/N1,518 (NXP Semiconductors)IC CNTL BALLAST 600V 16-SOIC PDF资料下载
参数资料
| 型号： | UBA2014T/N1,518 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 7/19页 |
| 文件大小： | 0K |
| 描述： | IC CNTL BALLAST 600V 16-SOIC |
| 标准包装： | 1 |
| 类型： | 镇流器控制器 |
| 频率： | 40.5 ~ 100 kHz |
| 电流 - 电源： | 1.5mA |
| 电流 - 输出： | 330mA |
| 电源电压： | 9.1 V ~ 13 V |
| 工作温度： | -25°C ~ 80°C |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SO |
| 包装： | 标准包装 |
| 产品目录页面： | 844 (CN2011-ZH PDF) |
| 其它名称： | 568-3322-6 |
NXP Semiconductors
UBA2014
600 V driver IV for HF ?uorescent lamps
8.9 Power-down mode
The Power-down mode will be entered if, at the end of the ignition time, the voltage at
pin LVS is above V lamp(fail) . In the Power-down mode the oscillator will be stopped and
both TR1 and TR2 will be non-conductive. The V DD supply is internally clamped. The
circuit is released from the Power-down mode by lowering the low-voltage supply below
V DD(reset) .
8.10 Capacitive mode protection
The signal across R16 also gives information about the switching behavior of the half
bridge. If, after the preheat state, the voltage across the ACM resistor (R16) does not
exceed the V CMD level during the non-overlap time, the Capacitive Mode Detection (CMD)
circuit assumes that the circuit is in the capacitive mode of operation. As a consequence
the frequency will directly be increased to f max . The frequency behavior is decoupled from
the voltage at pin CSW until C CSW has been discharged to zero.
8.11 Charge coupling
Due to parasitic capacitive coupling to the high voltage circuitry all pins are burdened with
a repetitive charge injection. Given the typical application the pins IREF and CF are
sensitive to this charge injection. For charge coupling of approximately 8 pC, a safe
functional operation of the IC is guaranteed, independent of the current level.
Charge coupling at current levels below 50 μ A will not interfere with the accuracy of the
V CS , V PCS and V ACM levels.
Charge coupling at current levels below 20 μ A will not interfere with the accuracy of any
parameter.
8.12 Design equations
The following design equations are used to calculate the desired preheat time, the
maximum ignition time, and the minimum and the maximum switching frequency.
t ph = 1.8 × ------------------------- 9 - × ------------------- 3 -
330 × 10
33 × 10
t ign = 0.26 × ------------------------- 9 - × ------------------- 3 -
330 × 10
33 × 10
100 × 10
33 × 10
f min = 40.5 × 10 × ---------------------------- × --------------------
C CT R IREF
–
C CT R IREF
3
f max = 2.5 × f min
–
C CF R IREF
– 12 3
(1)
(2)
(3)
(4)
Start of ignition is de?ned as the moment at which the measured lamp voltage crosses the
UBA2014_4
? NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 04 — 16 October 2008
7 of 19
相关PDF资料 |
PDF描述 |
|---|---|
| VI-BTN-CV-F1 | CONVERTER MOD DC/DC 18.5V 150W |
| GMM43DRYN-S13 | CONN EDGECARD 86POS .156 EXTEND |
| VI-BT2-CV-F4 | CONVERTER MOD DC/DC 15V 150W |
| 4-1624113-7 | INDUCTOR .11UH 5% 0805 |
| HSM02DSEN | CONN EDGECARD 4POS .156 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| UBA2015 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:600 V fluorescent lamp driver with PFC, linear dimming and boost function |
| UBA2015A | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:600 V fluorescent lamp driver with PFC, linear dimming and boost function |
| UBA2015AP | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:600 V fluorescent lamp driver with PFC, linear dimming and boost function |
| UBA2015AP/1,112 | 功能描述:显示驱动器和控制器 600V 0.16mA DIP20 RoHS:否 制造商:Panasonic Electronic Components 工作电源电压:2.7 V to 5.5 V 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Reel |
| UBA2015APN1 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:600 V fluorescent lamp driver with PFC, linear dimming and boost function |
发布紧急采购，3分钟左右您将得到回复。