参数资料
| 型号： | UBA2070T/N1,518 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 16/20页 |
| 文件大小： | 0K |
| 描述： | IC CCFL DRIVER 16-SOIC |
| 标准包装： | 1 |
| 类型： | CCFL 驱动器 |
| 频率： | 40.5 ~ 100 kHz |
| 电流 - 电源： | 1.5mA |
| 电流 - 输出： | 300mA |
| 电源电压： | 6V |
| 工作温度： | -25°C ~ 80°C |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SO |
| 包装： | 标准包装 |
| 其它名称： | 568-4418-6 |
Philips Semiconductors
600 V CCFL ballast driver IC
SOLDERING
Introduction
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “Data Handbook IC26; Integrated Circuit Packages”
(document order number 9398 652 90011).
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mount components are mixed on
one printed-circuit board. Wave soldering can still be used
for certain surface mount ICs, but it is not suitable for fine
pitch SMDs. In these situations reflow soldering is
recommended.
Through-hole mount packages
S OLDERING BY DIPPING OR BY SOLDER WAVE
The maximum permissible temperature of the solder is
260 ° C; solder at this temperature must not be in contact
with the joints for more than 5 seconds. The total contact
time of successive solder waves must not exceed
5 seconds.
The device may be mounted up to the seating plane, but
the temperature of the plastic body must not exceed the
specified maximum storage temperature (T stg(max) ). If the
printed-circuit board has been pre-heated, forced cooling
may be necessary immediately after soldering to keep the
temperature within the permissible limit.
M ANUAL SOLDERING
Apply the soldering iron (24 V or less) to the lead(s) of the
package, either below the seating plane or not more than
2 mm above it. If the temperature of the soldering iron bit
is less than 300 ° C it may remain in contact for up to
10 seconds. If the bit temperature is between
300 and 400 ° C, contact may be up to 5 seconds.
Surface mount packages
R EFLOW SOLDERING
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several methods exist for reflowing; for example,
convection or convection/infrared heating in a conveyor
type oven. Throughput times (preheating, soldering and
cooling) vary between 100 and 200 seconds depending
on heating method.
2002 Oct 24
16
Product speci?cation
UBA2070
Typical reflow peak temperatures range from
215 to 250 ° C. The top-surface temperature of the
packages should preferable be kept below 220 ° C for
thick/large packages, and below 235 ° C for small/thin
packages.
W AVE SOLDERING
Conventional single wave soldering is not recommended
for surface mount devices (SMDs) or printed-circuit boards
with a high component density, as solder bridging and
non-wetting can present major problems.
To overcome these problems the double-wave soldering
method was specifically developed.
If wave soldering is used the following conditions must be
observed for optimal results:
? Use a double-wave soldering method comprising a
turbulent wave with high upward pressure followed by a
smooth laminar wave.
? For packages with leads on two sides and a pitch (e):
– larger than or equal to 1.27 mm, the footprint
longitudinal axis is preferred to be parallel to the
transport direction of the printed-circuit board;
– smaller than 1.27 mm, the footprint longitudinal axis
must be parallel to the transport direction of the
printed-circuit board.
The footprint must incorporate solder thieves at the
downstream end.
? For packages with leads on four sides, the footprint must
be placed at a 45 ° angle to the transport direction of the
printed-circuit board. The footprint must incorporate
solder thieves downstream and at the side corners.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Typical dwell time is 4 seconds at 250 ° C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
M ANUAL SOLDERING
Fix the component by first soldering two
diagonally-opposite end leads. Use a low voltage (24 V or
less) soldering iron applied to the flat part of the lead.
Contact time must be limited to 10 seconds at up to
300 ° C. When using a dedicated tool, all other leads can
be soldered in one operation within 2 to 5 seconds
between 270 and 320 ° C.
相关PDF资料 |
PDF描述 |
|---|---|
| UBA2071ATS/N1,118 | IC DVR HALF BRIDGE 24-SSOP |
| UC3843ANG | IC REG CTRLR FLYBK ISO PWM 8-DIP |
| UC3844BVD1R2G | IC REG CTRLR PWM CM 8-SOIC |
| UC3845NG | IC REG CTRLR PWM CM 8-DIP |
| UCC28250PW | IC REG CTRLR PWM CM/VM 20-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| UBA2071 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Half bridge control IC for CCFL backlighting |
| UBA2071AT | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Half bridge control IC for CCFL backlighting |
| UBA2071AT/N1,118 | 功能描述:显示驱动器和控制器 CCFL DRVR 14V 24-Pin RoHS:否 制造商:Panasonic Electronic Components 工作电源电压:2.7 V to 5.5 V 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Reel |
| UBA2071AT/N1118 | 制造商:Rochester Electronics LLC 功能描述: 制造商:NXP 功能描述: 制造商:NXP Semiconductors 功能描述: |
| UBA2071ATS | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Half bridge control IC for CCFL backlighting |
发布紧急采购，3分钟左右您将得到回复。