参数资料
| 型号： | UCC2893D |
| 厂商： | Texas Instruments |
| 文件页数： | 10/41页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR FLYBK ISO CM 16SOIC |
| 标准包装： | 40 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 1MHz |
| 占空比： | 74% |
| 电源电压： | 8.5 V ~ 16 V |
| 降压： | 无 |
| 升压： | 无 |
| 回扫： | 是 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 是 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 包装： | 管件 |
| 其它名称： | 296-15886-5 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页
UCC2891, UCC2892
UCC2893, UCC2894
SLUS542F ? OCTOBER 2003 ? REVISED JULY 2009
DETAILED PIN DESCRIPTIONS (continued)
FB (pin 9)
This pin is an input for the control voltage of the pulse width modulator of the UCC2891 family. The control
voltage is generated by an external error amplifier by comparing the converters output voltage to a voltage
reference and employing the compensation for the voltage regulation loop. Usually, the error amplifier is located
on the secondary side of the isolated power converter and its output voltage is sent across the isolation
boundary by an opto coupler. Thus, the FB pin is usually driven by the opto coupler. An external pull-up resistor
to the VREF pin (pin 4) is also needed for proper operation as part of the feedback circuitry.
The control voltage is internally buffered and connected to the PWM comparator through a voltage divider to
make it compatible to the signal level of the current sense circuit. The useful voltage range of the FB pin is
between approximately 1.25 V and 4.5 V. Control voltages below the 1.25-V threshold result in zero duty cycle
(pulse skipping) while voltages above 4.5 V result in full duty cycle (D MAX ) operation.
SS/SD (pin 10)
A capacitor (C SS ) connected between this pin and GND (pin 6) programs the soft start time of the power
converter. The soft-start capacitor is charged by a precise, internal DC current source which is programmed by
the R ON resistor connected to pin 2. The soft-start current is defined as:
I SS + 0.43
I RTON + 0.43
V REF
2
1
R ON
(6)
This DC current charges C SS from 0 V to approximately 5 V. Internal to the UCC2891 family of controllers, the
soft start capacitor voltage is buffered and ORed with the control voltage present at the FB pin (pin 9). The lower
of the two voltages manipulates the controller’s PWM engine through the voltage divider described with regards
to the FB pin. Accordingly, the useful control range on the SS pin is similar to the control range of the FB pin
and it is between 1.25 V and 4.5 V approximately.
PGND (pin 11)
This pin serves as a dedicated connection to all high-current circuits inside the UCC2891 family of parts. The
high-current portion of the controller consists of the two high-current gate drivers, and the various bias
connections except VREF (pin 4). The PGND (pin 11) and GND (pin 6) pins are not connected internally, a
low-impedance, external connection between the two ground pins is also required. It is recommended to form
a separate ground plane for the low current setup components (R DEL , R ON , R OFF , C VREF , C F , R SLOPE , C SS and
the emitter of the opto-coupler in the feedback circuit). This separate ground plane (GND) should have a single
connection to the rest of the ground of the power converter (PGND) and this connection should be between pin
6 and pin 11 of the controller.
AUX (pin 12)
This is a high-current gate drive output for the auxiliary switch to implement the active clamp operation for the
power stage. The auxiliary output (AUX) of the UCC2891 and UCC2892 drives a P-channel device as the clamp
switch therefore it requires an active low operation (the switch is ON when the output is low). The UCC2893
and UCC2894 controllers are optimized for N-channel auxiliary switch therefore it employs the traditional active
high drive signal.
10
www.ti.com
相关PDF资料 |
PDF描述 |
|---|---|
| UCC3957MTR-2G4 | IC LI-ION PROTECT CIRCUIT 16QSOP |
| UDN2982LWTR-T | IC SOURCE DRIVER 8CHAN 20-SOIC |
| UDN2987LW-6-T | IC SOURCE DRIVER 8CHAN 20-SOIC |
| UDQ2916LBTR-T | IC MOTOR DRIVER PWM DUAL 24SOIC |
| UDW2 | SCOTCHLOK INLINE 4-WIRE 16-19AWG |
相关代理商/技术参数 |
参数描述 |
|---|---|
| UCC2893DG4 | 功能描述:电流型 PWM 控制器 Current Mode Active Clamp RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| UCC2893DR | 功能描述:电流型 PWM 控制器 Current Mode Active Clamp RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| UCC2893DRG4 | 功能描述:电流型 PWM 控制器 Current Mode Active Clamp RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| UCC2893PW | 功能描述:电流型 PWM 控制器 Current Mode Active Clamp RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| UCC2893PWG4 | 功能描述:电流型 PWM 控制器 Current Mode Active Clamp RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。