参数资料
| 型号： | UCC2893D |
| 厂商： | Texas Instruments |
| 文件页数： | 11/41页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR FLYBK ISO CM 16SOIC |
| 标准包装： | 40 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 1MHz |
| 占空比： | 74% |
| 电源电压： | 8.5 V ~ 16 V |
| 降压： | 无 |
| 升压： | 无 |
| 回扫： | 是 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 是 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 包装： | 管件 |
| 其它名称： | 296-15886-5 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页
UCC2891, UCC2892
UCC2893, UCC2894
SLUS542F ? OCTOBER 2003 ? REVISED JULY 2009
DETAILED PIN DESCRIPTIONS (continued)
OUT (pin 13)
This high-current output drives an external N-channel MOSFET. Each controller in the UCC2891 family uses
active high drive signals for the main switch of the converter.
Due to the high speed and high-drive current capability of these outputs (AUX, OUT) the parasitic inductance
of the external circuit components connected to these pins should be carefully minimized. A potential way of
avoiding unnecessary parasitic inductances in the gate drive circuit is to place the controller in close proximity
to the MOSFETs and by ensuring that the outputs (AUX, OUT) and the gates of the MOSFET devices are
connected by wide, overlapping traces.
VDD (pin 14)
The VDD rail is the primary bias for the internal, high-current gate drivers, the internal 5-V bias regulator and
for parts of the undervoltage lockout circuit. To reduce switching noise on the bias rail, a good quality ceramic
capacitor (C HF ) must be placed very closely between the VDD pin and PGND (pin 11) to provide adequate
filtering. The recommended C HF value is 1- μ F for most applications but its value might be affected by the
properties of the external MOSFET transistors used in the power stage.
In addition to the low-impedance, high-frequency filtering, the controller’s bias rail requires a larger value energy
storage capacitor (C BIAS ) connected parallel to C HF . The energy storage capacitor must provide the hold up time
to operate the UCC2891 family (including gate drive power requirements) during start up. In steady state
operation the controller must be powered from a bootstrap winding off the power transformer or by an auxiliary
bias supply. In case of an independent auxiliary bias supply, the energy storage is provided by the output
capacitance of the bias supply. When using the internal JFET for startup, the external load on VDD must be
limited to less than 4 mA.
LINEUV (pin 15)
This input monitors the incoming power source to provide an accurate undervoltage lockout function with user
programmable hysteresis for the power supply controlled by the UCC2891 family. The unique property of the
UCC2891 family is to use only one pin to implement these functions without sacrificing on performance. The
input voltage of the power supply is scaled to the precise 1.27-V threshold of the undervoltage lockout
comparator by an external resistor divider (R IN1 , R IN2 in Figure 7). Once the line monitor ’s input threshold is
exceeded, an internal current source gets connected to the LINEUV pin. The current generator is programmed
by the R DEL resistor connected to pin 1 of the controller. The actual current level is given as:
I HYST +
V REF
2
1
R DEL
0.05
(7)
As this current flows through R IN2 of the input divider, the undervoltage lockout hysteresis is a function of I HYST
and R IN2 allowing accurate programming of the hysteresis of the line monitoring circuit.
For more information on how to program the line monitoring function refer to the Setup Guide of this datasheet.
www.ti.com
11
相关PDF资料 |
PDF描述 |
|---|---|
| UCC3957MTR-2G4 | IC LI-ION PROTECT CIRCUIT 16QSOP |
| UDN2982LWTR-T | IC SOURCE DRIVER 8CHAN 20-SOIC |
| UDN2987LW-6-T | IC SOURCE DRIVER 8CHAN 20-SOIC |
| UDQ2916LBTR-T | IC MOTOR DRIVER PWM DUAL 24SOIC |
| UDW2 | SCOTCHLOK INLINE 4-WIRE 16-19AWG |
相关代理商/技术参数 |
参数描述 |
|---|---|
| UCC2893DG4 | 功能描述:电流型 PWM 控制器 Current Mode Active Clamp RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| UCC2893DR | 功能描述:电流型 PWM 控制器 Current Mode Active Clamp RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| UCC2893DRG4 | 功能描述:电流型 PWM 控制器 Current Mode Active Clamp RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| UCC2893PW | 功能描述:电流型 PWM 控制器 Current Mode Active Clamp RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| UCC2893PWG4 | 功能描述:电流型 PWM 控制器 Current Mode Active Clamp RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。