参数资料
| 型号： | UCC2893D |
| 厂商： | Texas Instruments |
| 文件页数： | 9/41页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR FLYBK ISO CM 16SOIC |
| 标准包装： | 40 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 1MHz |
| 占空比： | 74% |
| 电源电压： | 8.5 V ~ 16 V |
| 降压： | 无 |
| 升压： | 无 |
| 回扫： | 是 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 是 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 包装： | 管件 |
| 其它名称： | 296-15886-5 |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页
UCC2891, UCC2892
UCC2893, UCC2894
SLUS542F ? OCTOBER 2003 ? REVISED JULY 2009
DETAILED PIN DESCRIPTIONS (continued)
SYNC (pin 5)
This pin provides an input for an external clock signal which can be used to synchronize the internal oscillator
of the UCC289x family of controllers. The synchronizing frequency must be higher than the free running
frequency of the onboard oscillator
T SYNC t T SW . The acceptable minimum pulse width of the
synchronization signal is approximately 50 ns (positive logic), and it should remain shorter than
1 * D MAX
T SYNC where D MAX is set by R ON and R OFF . If the pulse width of the synchronization signal stays
within these limits, the maximum operating duty ratio remains valid as defined by the ratio of R ON and R OFF ,
and D MAX is the same in free running and in synchronized modes of operation. If the pulse width of the
synchronization signal would exceed the 1 * D MAX
T SYNC limit, the maximum operating duty cycle is
defined by the synchronization pulse width.
For more information on synchronization of the UCC2891 family refer to the Functional Description section of
this datasheet.
GND (pin 6)
This pin provides a reference potential for all small signal control and programming circuitry inside the UCC2891
family.
CS (pin 7)
This is a direct input to the PWM and current limit comparators of the UCC2891 family of controllers. The CS
pin should never be connected directly across the current sense resistor (R CS ) of the power converter. A small,
customary R?C filter between the current sense resistor and the CS pin is necessary to accommodate the
proper operation of the onboard slope compensation circuit and in order to protect the internal discharge
transistor connected to the CS pin (R F , C F ).
Slope compensation is achieved across R F by a linearly increasing current flowing out of the CS pin. The slope
compensation current is only present during the on-time of the gate drive signal of the main power switch (OUT)
of the converter. The internal pull-down transistor of the CS pin is activated during the discharge time of the
timing capacitor. This time interval is 1 * D MAX
T SW long and represents the guaranteed off time of the
main power switch.
RSLOPE (pin 8)
A resistor (R SLOPE ) connected between this pin and GND (pin 6) sets the amplitude of the slope compensation
current. During the on time of the main gate drive output (OUT) the voltage across R SLOPE is a representation
of the internal timing capacitor waveform. As the timing capacitor is being charged, the voltage across R SLOPE
also increases, generating a linearly increasing current waveform. The current provided at the CS pin for slope
compensation is proportional to this current flowing through R SLOPE .
Due to the high speed, AC voltage waveform present at the RSLOPE pin, the parasitic capacitance and
inductance of the external circuit components connected to the RSLOPE pin should be carefully minimized.
For more information on how to program the internal slope compensation refer to the Setup Guide section of
this datasheet.
www.ti.com
9
相关PDF资料 |
PDF描述 |
|---|---|
| UCC3957MTR-2G4 | IC LI-ION PROTECT CIRCUIT 16QSOP |
| UDN2982LWTR-T | IC SOURCE DRIVER 8CHAN 20-SOIC |
| UDN2987LW-6-T | IC SOURCE DRIVER 8CHAN 20-SOIC |
| UDQ2916LBTR-T | IC MOTOR DRIVER PWM DUAL 24SOIC |
| UDW2 | SCOTCHLOK INLINE 4-WIRE 16-19AWG |
相关代理商/技术参数 |
参数描述 |
|---|---|
| UCC2893DG4 | 功能描述:电流型 PWM 控制器 Current Mode Active Clamp RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| UCC2893DR | 功能描述:电流型 PWM 控制器 Current Mode Active Clamp RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| UCC2893DRG4 | 功能描述:电流型 PWM 控制器 Current Mode Active Clamp RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| UCC2893PW | 功能描述:电流型 PWM 控制器 Current Mode Active Clamp RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| UCC2893PWG4 | 功能描述:电流型 PWM 控制器 Current Mode Active Clamp RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。