- 您现在的位置：买卖IC网 > PDF目录361590 > UPSD3212AV-24T6T (意法半导体) Flash Programmable System Devices with 8032 MCU with USB and Programmable Logic PDF资料下载
参数资料
| 型号： | UPSD3212AV-24T6T |
| 厂商： | 意法半导体 |
| 英文描述： | Flash Programmable System Devices with 8032 MCU with USB and Programmable Logic |
| 中文描述： | 闪存可编程系统设备与8032具有USB和可编程逻辑控制器 |
| 文件页数： | 93/163页 |
| 文件大小： | 2844K |
| 代理商： | UPSD3212AV-24T6T |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页当前第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页第162页第163页
93/163
uPSD3212A, uPSD3212C, uPSD3212CV
PSD MODULE DETAILED OPERATION
As shown in
Figure 15., page 27
, the PSD MOD-
ULE consists of five major types of functional
blocks:
Memory Block
PLD Blocks
I/O Ports
Power Management Unit (PMU)
JTAG Interface
The functions of each block are described in the
following sections. Many of the blocks perform
multiple functions, and are user configurable.
■
■
■
■
■
MEMORY BLOCKS
The PSD MODULE has the following memory
blocks:
Primary Flash memory
Secondary Flash memory
SRAM
The Memory Select signals for these blocks origi-
nate from the Decode PLD (DPLD) and are user-
defined in PSDsoft Express.
Primary Flash Memory and Secondary Flash
memory Description
The primary Flash memory is divided into 4 sec-
tors (16KBytes each). The secondary Flash mem-
ory is divided into 2 sectors (8KBytes each). Each
sector of either memory block can be separately
protected from Program and Erase cycles.
Flash memory may be erased on a sector-by-sec-
tor basis. Flash sector erasure may be suspended
while data is read from other sectors of the block
and then resumed after reading.
During a Program or Erase cycle in Flash memory,
the status can be output on Ready/Busy (PC3).
This pin is set up using PSDsoft Express Configu-
ration.
■
■
■
Memory Block Select Signals
The DPLD generates the Select signals for all the
internal memory blocks (see
PLDs, page 106
).
Each of the eight sectors of the primary Flash
memory has a Select signal (FS0-FS3) which can
contain up to three product terms. Each of the 2
sectors of the secondary Flash memory has a Se-
lect signal (CSBOOT0-CSBOOT1) which can con-
tain up to three product terms. Having three
product terms for each Select signal allows a given
sector to be mapped in Program or Data space.
Ready/Busy (PC3).
This signal can be used to
output the Ready/Busy status of the Flash memo-
ry. The output on Ready/Busy (PC3) is a 0 (Busy)
when Flash memory is being written to, or
when
Flash memory is being erased. The output is a 1
(Ready) when no WRITE or Erase cycle is in
progress.
Memory Operation.
The primary Flash memory
and secondary Flash memory are addressed
through the MCU Bus. The MCU can access these
memories in one of two ways:
–
The MCU can execute a typical bus WRITE or
READ operation.
–
The MCU can execute a specific Flash
memory instruction
that consists of several
WRITE and READ operations. This involves
writing specific data patterns to special
addresses within the Flash memory to invoke
an embedded algorithm. These instructions
are summarized in Table
82
.
Typically, the MCU can read Flash memory using
READ operations, just as it would read a ROM de-
vice. However, Flash memory can only be altered
using specific Erase and Program instructions. For
example, the MCU cannot write a single byte di-
rectly to Flash memory as it would write a byte to
RAM. To program a byte into Flash memory, the
MCU must execute a Program instruction, then
test the status of the Program cycle. This status
test is achieved by a READ operation or polling
Ready/Busy (PC3).
相关PDF资料 |
PDF描述 |
|---|---|
| UPSD3212AV-24U6T | Flash Programmable System Devices with 8032 MCU with USB and Programmable Logic |
| UPSD3212AV-40T6T | Flash Programmable System Devices with 8032 MCU with USB and Programmable Logic |
| UPSD3212AV-40U6T | Flash Programmable System Devices with 8032 MCU with USB and Programmable Logic |
| UPSD3212CV-24T6 | Flash Programmable System Devices with 8032 MCU with USB and Programmable Logic |
| UPSD3212CV-24U6 | Flash Programmable System Devices with 8032 MCU with USB and Programmable Logic |
相关代理商/技术参数 |
参数描述 |
|---|---|
| UPSD3212AV-24U6T | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Flash Programmable System Devices with 8032 MCU with USB and Programmable Logic |
| UPSD3212AV-40T6T | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Flash Programmable System Devices with 8032 MCU with USB and Programmable Logic |
| UPSD3212AV-40U6T | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Flash Programmable System Devices with 8032 MCU with USB and Programmable Logic |
| UPSD3212C | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Flash Programmable System Devices with 8032 MCU with USB and Programmable Logic |
| UPSD3212C-24T1T | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Flash Programmable System Devices with 8032 Microcontroller Core and 16Kbit SRAM |
发布紧急采购，3分钟左右您将得到回复。