- 您现在的位置：买卖IC网 > PDF目录11591 > VNC2-64Q1B-REEL (FTDI, Future Technology Devices International Ltd)IC USB HOST/DEVICE CTRL 64-QFN PDF资料下载
参数资料
| 型号： | VNC2-64Q1B-REEL |
| 厂商： | FTDI, Future Technology Devices International Ltd |
| 文件页数： | 16/88页 |
| 文件大小： | 0K |
| 描述： | IC USB HOST/DEVICE CTRL 64-QFN |
| 应用说明： | Vinculum-II IO Cell Description AppNote Vinculum-II Debug Interface Description AppNote Vinculum-II IO Mux Explained AppNote Vinculum-II PWM Example AppNote Migrating Vinculum Designs AppNote |
| 特色产品： | Vinculum VNC2 |
| 标准包装： | 1 |
| 系列： | Vinculum-II |
| 控制器类型： | USB 2.0 控制器 |
| 接口： | USB，主机/设备配置，UART，SPI，PWM，闪存 256K，DMA 4CH |
| 电源电压： | 1.62 V ~ 1.98 V |
| 电流 - 电源： | 25mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-VFQFN 裸露焊盘 |
| 供应商设备封装： | 64-QFN（8x8） |
| 包装： | 标准包装 |
| 产品目录页面： | 634 (CN2011-ZH PDF) |
| 其它名称： | 768-1046-6 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页
23
Copyright 2009-2011 Future Technology Devices International Limited
Datasheet
Vinculum-II Embedded Dual USB Host Controller IC
Version 1.5
Document No.: FT_000138 Clearance No.: FTDI# 143
4.2.5 Peripheral DMA Modules 0, 1, 2 & 3
The peripheral DMA has the capability to transfer data to and from an I/O device. The CPU can offload
the transfer of data between the processor and the peripheral freeing the CPU to execute other
instructions.
The DMA module collects or transmits data from memory to an I/O address space, it is also capable of
copying data in memory and transferring it to another location.
The DMA is not accessible by the user as it automatically controlled by the CPU.
4.2.6 RAM Module
The RAM module consists of 16k bytes on-chip (4k x 32-bits) data memory. The RAM is byte addressable.
4.2.7 Peripheral Interface Modules
VNC2 has nine peripheral interface modules. Full descriptions of each module are described in section 6.
Debugger Interface
UART
PWM
FIFO
SPI Master
SPI Slave 0 & 1
GPIO - General purpose I/O pins
General purpose timers
4.2.8 USB Transceivers 0 and 1
Two USB transceiver cells provide the physical USB device interface supporting USB 1.1 and USB 2.0
standards. Low-speed and full-speed USB data rates are supported. Each output driver provides +3.3V
level slew rate control signalling, whilst a differential receiver and two single ended receivers provide USB
DATA IN, SE0 and USB Reset condition detection. These cells also include integrated internal USB pull-up
or pull-down resistors as required for host or slave mode.
4.2.9 USB Host / Device Controllers
These blocks handle the parallel-to-serial and serial-to-parallel conversion of the USB physical layer. This
includes bit stuffing, CRC generation, USB frame generation and protocol error checking. The Host /
Device controller is autonomous and therefore requires limited load from the CPU.
4.2.10 12MHz Oscillator
The 12MHz Oscillator cell generates a 12MHz reference clock input to the Clock Multiplier PLL from an
external 12MHz crystal. The external crystal is connected across Pin 4 – XTIN and Pin 5 – XTOUT in the
configuration shown in Figure 10.1.
4.2.11 Power Saving Modes and Standby mode.
VNC2 can be set to operate in three frequencies allowing the user to select a slower speed to reduce
power consumption. Three operating frequencies available are 12MHz, 24MHz and normal operation of
48MHz. These operating modes can be configured using the RTOS. Full details are available in the RTOS
manual available from the FTDI website.
When a particular peripheral is not used, it is powered down internally thus saving power.
Standby mode is available under firmware control, this mode puts the VNC2 in a state with no clocks
running or system blocks powered. The device will wake up out of this mode by toggling any of the
following signals: USB0/1 DP or DM, SPI slave 0 select (spi_s0_ss# ), SPI slave 1select(spi_s1_ss# ) or
UART ring indicator (uart_ri#).
相关PDF资料 |
PDF描述 |
|---|---|
| V72A48C400BF2 | CONVERTER MOD DC/DC 48V 400W |
| PIC16F1827-E/SO | MCU PIC 8BIT 4K FLASH 18-SOIC |
| PIC16F1826T-I/MV | MCU PIC 8BIT 2K FLASH 28-UQFN |
| PIC16F1826T-I/ML | MCU PIC 8BIT 2K FLASH 28-QFN |
| PIC24F04KA201T-I/MQ | IC PIC MCU FLASH 512KX4 20-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| VNC2-64Q1B-TRAY | 功能描述:USB 接口集成电路 Vinculum-II Dual Host/Dev IC QFN-64 RoHS:否 制造商:Cypress Semiconductor 产品:USB 2.0 数据速率: 接口类型:SPI 工作电源电压:3.15 V to 3.45 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:WLCSP-20 |
| VNC2DEBUGMODULE | 制造商:Future Technology Devices International (FTDI Chip) 功能描述:VNC2 Vinculum Debug Module |
| VNC712B-N50A-5TZ | 制造商:SMC Corporation of America 功能描述:Valve, media, coolant, 2 way |
| VNC-DK4-C1404CM | 制造商:L-com Inc 功能描述:4CH DVR w/4 CMOS CAMERAS no HD |
| VNC-DK4-C1404CM-HD | 制造商:L-com Inc 功能描述:4CH DVR w/4 CMOS CAMS 500GB HD |
发布紧急采购，3分钟左右您将得到回复。