参数资料
型号: W25X40BVZPIG
厂商: Winbond Electronics
文件页数: 18/51页
文件大小: 0K
描述: IC SPI FLASH 4MBIT 8WSON
标准包装: 100
系列: SpiFlash®
格式 - 存储器: 闪存
存储器类型: FLASH
存储容量: 4M (512K x 8)
速度: 104MHz
接口: SPI 串行
电源电压: 2.7 V ~ 3.6 V
工作温度: -40°C ~ 85°C
封装/外壳: 8-WDFN 裸露焊盘
供应商设备封装: 8-WSON(6x5)
包装: 管件
W25X10BV/20BV/40BV
9.2.6
Write Status Register (01h)
The Write Status Register instruction allows the Status Register to be written. A Write Enable
instruction must previously have been executed for the device to accept the Write Status Register
Instruction (Status Register bit WEL must equal 1). Once write enabled, the instruction is entered by
driving /CS low, sending the instruction code “01h”, and then writing the status register data byte as
illustrated in figure 7. The Status Register bits are shown in figure 3 and described earlier in this
datasheet.
Only non-volatile Status Register bits SRP, TB, BP2, BP1 and BP0 (bits 7, 5, 4, 3 and 2) can be
written to. All other Status Register bit locations are read-only and will not be affected by the Write
Status Register instruction.
The /CS pin must be driven high after the eighth bit of the last byte has been latched. If this is not
done the Write Status Register instruction will not be executed. After /CS is driven high, the self-timed
Write Status Register cycle will commence for a time duration of t W (See AC Characteristics). While
the Write Status Register cycle is in progress, the Read Status Register instruction may still accessed
to check the status of the BUSY bit. The BUSY bit is a 1 during the Write Status Register cycle and a
0 when the cycle is finished and ready to accept other instructions again. After the Write Register
cycle has finished the Write Enable Latch (WEL) bit in the Status Register will be cleared to 0.
The Write Status Register instruction allows the Block Protect bits (TB, BP2, BP1 and BP0) to be set
for protecting all, a portion, or none of the memory from erase and program instructions. Protected
areas become read-only (see Status Register Memory Protection table). The Write Status Register
instruction also allows the Status Register Protect bit (SRP) to be set. This bit is used in conjunction
with the Write Protect (/WP) pin to disable writes to the status register. When the SRP bit is set to a 0
state (factory default) the /WP pin has no control over the status register. When the SRP pin is set to a
1, the Write Status Register instruction is locked out while the /WP pin is low. When the /WP pin is
high the Write Status Register instruction is allowed.
Figure 7. Write Status Register Instruction Sequence Diagram
- 18 -
相关PDF资料
PDF描述
W25X64VZEIG IC FLASH 64MBIT 75MHZ 8WSON
W25X80AVDAIZ IC FLASH 16MBIT 100MHZ 8DIP
W29GL032CB7A IC FLASH 32MBIT 70NS 48TFBGA
W29GL064CB7S IC FLASH 64MBIT 70NS 48TSOP
W29GL128CL9T IC FLASH 128MBIT 90NS 56TSOP
相关代理商/技术参数
参数描述
W25X40CLDAIG 制造商:Winbond Electronics Corp 功能描述:IC FLASH 4MBIT 104MHZ 制造商:Winbond Electronics Corp 功能描述:IC FLASH 4MBIT 104MHZ 8DIP
W25X40CLSNIG 功能描述:IC FLASH SPI 4MBIT 8SOIC RoHS:是 类别:集成电路 (IC) >> 存储器 系列:SpiFlash® 标准包装:2,000 系列:- 格式 - 存储器:RAM 存储器类型:SRAM - 异步 存储容量:256K (32K x 8) 速度:15ns 接口:并联 电源电压:3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 封装/外壳:28-TSSOP(0.465",11.8mm 宽) 供应商设备封装:28-TSOP 包装:带卷 (TR) 其它名称:71V256SA15PZGI8
W25X40CLSNIG TR 制造商:Winbond Electronics Corp 功能描述:SPIFLASH, 4M-BIT, 4KB UNIFORM 制造商:Winbond Electronics Corp 功能描述:IC MEMORY 制造商:Winbond 功能描述:SPIFLASH, 4M-BIT, 4KB UNIFORM
W25X40CLSSIG 功能描述:IC FLASH SPI 4MBIT 8SOIC RoHS:是 类别:集成电路 (IC) >> 存储器 系列:SpiFlash® 标准包装:2,000 系列:- 格式 - 存储器:RAM 存储器类型:SRAM - 异步 存储容量:256K (32K x 8) 速度:15ns 接口:并联 电源电压:3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 封装/外壳:28-TSSOP(0.465",11.8mm 宽) 供应商设备封装:28-TSOP 包装:带卷 (TR) 其它名称:71V256SA15PZGI8
W25X40CLUXIG TR 制造商:Winbond Electronics Corp 功能描述:NOT IN PRICE BOOK CONSULT FACT