W25X80AVDAIZ (Winbond Electronics) Datasheet资料下载 PDF(18/45 页)

您现在的位置：买卖IC网 > Datasheet目录368 > W25X80AVDAIZ (Winbond Electronics)IC FLASH 16MBIT 100MHZ 8DIP Datasheet资料下载

参数资料

W25X10A, W25X20A, W25X40A, W25X80A

10.2.6 Write Status Register (01h)

The Write Status Register instruction allows the Status Register to be written. A Write Enable

instruction must previously have been executed for the device to accept the Write Status Register

Instruction (Status Register bit WEL must equal 1). Once write enabled, the instruction is entered by

driving /CS low, sending the instruction code “01h”, and then writing the status register data byte as

illustrated in figure 7. The Status Register bits are shown in figure 3 and described earlier in this

datasheet.

Only non-volatile Status Register bits SRP, TB, BP2, BP1 and BP0 (bits 7, 5, 4, 3 and 2) can be

written to. All other Status Register bit locations are read-only and will not be affected by the Write

Status Register instruction.

The /CS pin must be driven high after the eighth bit of the last byte has been latched. If this is not

done the Write Status Register instruction will not be executed. After /CS is driven high, the self-timed

Write Status Register cycle will commence for a time duration of t W (See AC Characteristics). While

the Write Status Register cycle is in progress, the Read Status Register instruction may still accessed

to check the status of the BUSY bit. The BUSY bit is a 1 during the Write Status Register cycle and a

0 when the cycle is finished and ready to accept other instructions again. After the Write Register

cycle has finished the Write Enable Latch (WEL) bit in the Status Register will be cleared to 0.

The Write Status Register instruction allows the Block Protect bits (TB, BP2, BP1 and BP0) to be set

for protecting all, a portion, or none of the memory from erase and program instructions. Protected

areas become read-only (see Status Register Memory Protection table). The Write Status Register

instruction also allows the Status Register Protect bit (SRP) to be set. This bit is used in conjunction

with the Write Protect (/WP) pin to disable writes to the status register. When the SRP bit is set to a 0

state (factory default) the /WP pin has no control over the status register. When the SRP pin is set to a

1, the Write Status Register instruction is locked out while the /WP pin is low. When the /WP pin is

high the Write Status Register instruction is allowed.

Figure 7. Write Status Register Instruction Sequence Diagram

- 18 -

相关代理商/技术参数	参数描述
W25X80AVSNIG	制造商:WINBOND 制造商全称:Winbond 功能描述:1M-BIT, 2M-BIT, 4M-BIT AND 8M-BIT SERIAL FLASH MEMORY WITH 4KB SECTORS AND DUAL OUTPUT SPI
W25X80AVSSIG	功能描述:IC FLASH 16MBIT 100MHZ 8SOIC RoHS:是类别:集成电路 (IC) >> 存储器系列:SpiFlash® 产品变化通告:Product Discontinuation 26/Apr/2010 标准包装:136 系列:- 格式 - 存储器:RAM 存储器类型:SRAM - 同步，DDR II 存储容量:18M（1M x 18）速度:200MHz 接口:并联电源电压:1.7 V ~ 1.9 V 工作温度:0°C ~ 70°C 封装/外壳:165-TBGA 供应商设备封装:165-CABGA（13x15）包装:托盘其它名称:71P71804S200BQ
W25X80AVZPIG	功能描述:IC FLASH 16MBIT 100MHZ 8WSON RoHS:是类别:集成电路 (IC) >> 存储器系列:SpiFlash® 产品变化通告:Product Discontinuation 26/Apr/2010 标准包装:136 系列:- 格式 - 存储器:RAM 存储器类型:SRAM - 同步，DDR II 存储容量:18M（1M x 18）速度:200MHz 接口:并联电源电压:1.7 V ~ 1.9 V 工作温度:0°C ~ 70°C 封装/外壳:165-TBGA 供应商设备封装:165-CABGA（13x15）包装:托盘其它名称:71P71804S200BQ
W25X80L	制造商:WINBOND 制造商全称:Winbond 功能描述:1M-BIT, 2M-BIT, 4M-BIT AND 8M-BIT 2.5V SERIAL FLASH MEMORY WITH 4KB SECTORS AND DUAL OUTPUT SPI
W25X80LDAC	制造商:WINBOND 制造商全称:Winbond 功能描述:1M-BIT, 2M-BIT, 4M-BIT AND 8M-BIT SERIAL FLASH MEMORY WITH 4KB SECTORS AND DUAL OUTPUT SPI

发布紧急采购，3分钟左右您将得到回复。

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购