- 您现在的位置：买卖IC网 > PDF目录68459 > W671310P (WINBOND ELECTRONICS CORP) TELECOM-SLIC, PQCC28 PDF资料下载
参数资料
| 型号： | W671310P |
| 厂商： | WINBOND ELECTRONICS CORP |
| 元件分类： | 模拟传输电路 |
| 英文描述： | TELECOM-SLIC, PQCC28 |
| 封装： | PLASTIC, LCC-28 |
| 文件页数： | 24/48页 |
| 文件大小： | 1344K |
| 代理商： | W671310P |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
W671300 SERIES
operating mode.
7.2.5. UNBALANCED RINGING MODE
The W671370 and W671371 also offer an Unbalanced Ringing mode (010). This feature is important
for those Analog PBX Trunk Lines that require the Tip terminal to be held near ground for the duration
of the ringing bursts. The Tip terminal is offset to 0V using an internal current source that is applied to
the inverting input of the Tip amplifier. This reduces the differential ringing gain to 40V/V. The Ring
terminal will center at VBH/2 and swing from -VBH to ground. As in Balanced Ringing mode, off-hook
detection is accomplished by sensing the peak current and comparing it to a preset threshold. This
allows the same sensing, comparing and threshold circuitry to be used in both Ringing and
Unbalanced Ringing modes. This mode of operation does not require any additional external
components.
7.2.6. FORWARD LOOP BACK MODE
The Forward Loop Back mode (FLB, 101) provides test capability for the device. An internal signal
path is enabled allowing for both DC and AC verification. The internal 600 terminating resistor has a
tolerance of ±20%. The device is intended to operate from only the low battery during this mode.
7.2.6.1. Architecture
When the Forward Loop Back mode is initiated internal switches connect a 600 load across the
outputs of the Tip and Ring amplifiers.
RING AMP
TIP AMP
RING
TIP
600
FIGURE 13: FORWARD LOOP BACK INTERNAL TERMINATION
7.2.6.2. DC Verification
When the internal signal path is provided, DC current will flow from Tip to Ring. The DC current will
force DET LOW, indicating the presence of loop current. In addition, the ALM output will also go
LOW. In this mode this does not indicate a thermal alarm condition. Rather, proper logic operation is
verified in the event of a thermal shutdown. In addition to verifying device functionality, toggling the
logic outputs verifies the interface to the system controller.
- 30 -
相关PDF资料 |
PDF描述 |
|---|---|
| W671340P | TELECOM-SLIC, PQCC28 |
| W671352P | TELECOM-SLIC, PQCC28 |
| W671352Y | TELECOM-SLIC, QCC32 |
| W671371P | TELECOM-SLIC, PQCC28 |
| W671371Y | TELECOM-SLIC, QCC32 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| W674 | 功能描述:灯 S-8 INCND S.C. BAY RoHS:否 制造商:Chicago Miniature 灯类型:Incandescent 灯座类型:Wire Terminal 灯大小:T-1 3/4 颜色: 电压:14 V 工作电流: MSCP:0.3 MSCP 寿命:40000 hr 封装:Bulk |
| W67-A1Q1-20 | 制造商:MA-COM 制造商全称:M/A-COM Technology Solutions, Inc. 功能描述:Magnetic Hydraulic Circuit Breakers |
| W67-A1Q3-20 | 制造商:MA-COM 制造商全称:M/A-COM Technology Solutions, Inc. 功能描述:Magnetic Hydraulic Circuit Breakers |
| W67-A1Q5-20 | 制造商:MA-COM 制造商全称:M/A-COM Technology Solutions, Inc. 功能描述:Magnetic Hydraulic Circuit Breakers |
| W67-A1S1-20 | 制造商:MA-COM 制造商全称:M/A-COM Technology Solutions, Inc. 功能描述:Magnetic Hydraulic Circuit Breakers |
发布紧急采购，3分钟左右您将得到回复。