- 您现在的位置：买卖IC网 > PDF目录205930 > X4003S8I-4.5A 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 PDF资料下载
参数资料
| 型号： | X4003S8I-4.5A |
| 元件分类： | 电源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| 封装： | PLASTIC, SOIC-8 |
| 文件页数： | 17/18页 |
| 文件大小： | 378K |
| 代理商： | X4003S8I-4.5A |
X4003/X4005
Characteristics subject to change without notice.
8 of 18
REV 1.1.3 4/30/02
www.xicor.com
Figure 7. Acknowledge Response From Receiver
Data Output
from Transmitter
Data Output
from Receiver
8
1
9
Start
Acknowledge
SCL from
Master
SERIAL WRITE OPERATIONS
Slave Address Byte
Following a start condition, the master must output a
slave address byte. This byte consists of several parts:
– a device type identier that is always ‘1011’.
– two bits of ‘0’.
– one bit of the slave command byte is a R/W bit. The
R/W bit of the slave address byte denes the opera-
tion to be performed. When the R/W bit is a one, then
a read operation is selected. A zero selects a write
operation. Refer to Figure 8.
– After loading the entire slave address byte from the
SDA bus, the device compares the input slave byte
data to the proper slave byte. Upon a correct com-
pare, the device outputs an acknowledge on the SDA
line.
Write Control Register
To write to the control register, the device requires the
slave address byte and a byte address. This gives the
master access to register. After receipt of the address
byte, the device responds with an acknowledge, and
awaits the data. After receiving the 8 bits of the data
byte, the device again responds with an acknowledge.
The master then terminates the transfer by generating
a stop condition, at which time the device begins the
internal write cycle to the nonvolatile memory. During
this internal write cycle, the device inputs are disabled,
so the device will not respond to any requests from the
master. If WP is HIGH, the control register cannot be
changed. A write to the control register will suppress
the acknowledge bit and no data in the control register
will change. With WP low, a second byte written to the
control register terminates the operation and no write
occurs.
Stops and Write Modes
Stop conditions that terminate write operations must
be sent by the master after sending 1 full data byte
plus the subsequent ACK signal. If a stop is issued in
the middle of a data byte, or before 1 full data byte plus
its associated ACK is sent, then the device will reset
itself without performing the write.
Figure 8. Write Control Register Sequence
0
Slave
Address
Byte
Address
Data
A
C
K
A
C
K
A
C
K
SDA Bus
Signals from
the Slave
Signals from
the Master
Star
t
Stop
1
0
1
0
11
1
相关PDF资料 |
PDF描述 |
|---|---|
| X40411S8I-C | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| X5169S8I | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| X5643S14I | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO14 |
| XA1N300M | POWER/SIGNAL RELAY, DPDT, MOMENTARY, 0.036A (COIL), 28VDC (COIL), 1008mW (COIL), 5A (CONTACT), 28VDC (CONTACT), SOCKET MOUNT |
| XJ7N300M | POWER/SIGNAL RELAY, DPDT, MOMENTARY, 0.036A (COIL), 28VDC (COIL), 1008mW (COIL), 5A (CONTACT), 28VDC (CONTACT), THROUGH HOLE-RIGHT ANGLE MOUNT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| X4003S8IZ | 功能描述:IC SUPERVISOR CPU I2C 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:低有效 复位超时:最小为 600 ms 电压 - 阀值:3.8V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) |
| X4003S8IZ-2.7 | 功能描述:IC SUPERVISOR CPU I2C 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:低有效 复位超时:最小为 600 ms 电压 - 阀值:3.8V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) |
| X4003S8IZ-2.7A | 功能描述:IC SUPERVISOR CPU I2C 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:低有效 复位超时:最小为 600 ms 电压 - 阀值:3.8V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) |
| X4003S8IZ-4.5A | 功能描述:IC SUPERVISOR CPU I2C 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:低有效 复位超时:最小为 600 ms 电压 - 阀值:3.8V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) |
| X4003S8Z | 功能描述:IC SUPERVISOR CPU I2C 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:低有效 复位超时:最小为 600 ms 电压 - 阀值:3.8V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。