参数资料
| 型号： | X40235S16I-A |
| 厂商： | Intersil |
| 文件页数： | 10/36页 |
| 文件大小： | 0K |
| 描述： | IC VOLTAGE MON TRPL EE 16-SOIC |
| 标准包装： | 94 |
| 类型： | 多压监控器 |
| 监视电压数目： | 3 |
| 输出： | 开路漏极，开路漏极 |
| 复位： | 高有效/低有效 |
| 复位超时： | 可调节/可选择 |
| 电压 - 阀值： | 1.75V，2.2V，2.95V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 16-SOIC |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
X40231, X40233, X40235, X40237, X40239
Depending upon the operation to be performed on
each of these individual parts, a 1, 2 or 3 Byte protocol
SA7
SA6 SA5
SA4
SA3
SA2
SA1
SA0
is used. All operations however must begin with the
Slave Address Byte being issued on the SDA pin. The
1 0 1
0
R/W
Slave address selects the part of the X4023x to be
addressed, and specifies if a Read or Write operation
is to be performed.
It should be noted that in order to perform a write oper-
DEVICE TYPE
IDENTIFIER
INTERNAL
DEVICE
ADDRESS
READ /
WRITE
ation to either a DCP or the EEPROM array, the Write
Enable Latch (WEL) bit must first be set (See “BL1,
BL0: Block Lock protection bits - (Nonvolatile)” on
page 18.)
Slave Address Byte
Following a START condition, the master must output
a Slave Address Byte (Refer to Figure 4). This byte
consists of three parts:
—The Device Type Identifier which consists of the most
significant four bits of the Slave Address (SA7 - SA4).
The Device Type Identifier must always be set to 1010
Internal Address
(SA3 - SA1)
000
010
111
Bit SA0
0
1
Internally Addressed
Device
EEPROM Array
CR Register
DCP
Operation
WRITE
READ
in order to select the X4023x.
—The next three bits (SA3 - SA1) are the Internal Device
Figure 4.
Slave Address Format
Address bits. Setting these bits to 000 internally
selects the EEPROM array, while setting these bits to
111 selects the DCP structures in the X4023x. The CR
Register may be selected using the Internal Device
Address 010.
—The Least Significant Bit of the Slave Address (SA0)
Byte is the R/W bit. This bit defines the operation to be
performed on the device being addressed (as defined
in the bits SA3 - SA1). When the R/W bit is “1”, then a
READ operation is selected. A “0” selects a WRITE
To perform acknowledge polling, the master issues a
START condition followed by a Slave Address Byte.
The Slave Address issued must contain a valid Inter-
nal Device Address. The LSB of the Slave Address
(R/W) can be set to either 1 or 0 in this case. If the
device is still busy with the high voltage cycle then no
ACKNOWLEDGE will be returned. If the device has
completed the write operation, an ACKNOWLEDGE
will be returned and the host can then proceed with a
read or write operation. (Refer to Figure 5)
operation (Refer to Figure 4)
DIGITALLY CONTROLLED POTENTIOMETERS
Nonvolatile Write Acknowledge Polling
After a nonvolatile write command sequence (for either
the EEPROM array, the Non Volatile Memory of a DCP
(NVM), or the CR Register) has been correctly issued
(including the final STOP condition), the X4023x ini-
tiates an internal high voltage write cycle. This cycle
typically requires 5 ms. During this time, no further
Read or Write commands can be issued to the device.
Write Acknowledge Polling is used to determine when
this high voltage write cycle has been completed.
10
DCP Functionality
The X4023x includes one or two independent resistor
arrays. For the 64, 100 or 256 tap XDCPs, these
arrays respectively contain 63, 99 discrete resistive
segments that are connected in series. (the 256 tap
resistor achieves an equivalent end to end resistance.)
The physical ends of each array are equivalent to the
fixed terminals of a mechanical potentiometer. At one
end of the resistor array the terminal connects to the
R Hx pin (x = 0,1,2).The other end of the resistor array
is connected to V SS inside the package.
FN8115.0
April 11, 2005
相关PDF资料 |
PDF描述 |
|---|---|
| 450MXG390MEFCSN30X45 | CAP ALUM 390UF 450V 20% SNAP-IN |
| 0925-392K | COIL RF 3.9UH MOLDED SHIELDED |
| AYM12DTMD-S664 | CONN EDGECARD 24POS R/A .156 |
| ISL6554CBZ | IC PWM CORE VOLTAGE REG 20-SOIC |
| X40233S16I-BT1 | IC VOLTAGE MON TRPL EE 16-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| X40235S16I-AT1 | 功能描述:IC VOLTAGE MON TRPL EE 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X40235S16I-B | 功能描述:IC VOLTAGE MON TRPL EE 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X40235S16I-BT1 | 功能描述:IC VOLTAGE MON TRPL EE 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X40237 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Triple Voltage Monitors, POR, 2 kbit EEPROM MEMORY, and Single/Dual DCP |
| X40237S16I-A | 功能描述:IC VOLTAGE MON TRPL EE 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。