参数资料
| 型号： | X40235S16I-A |
| 厂商： | Intersil |
| 文件页数： | 19/36页 |
| 文件大小： | 0K |
| 描述： | IC VOLTAGE MON TRPL EE 16-SOIC |
| 标准包装： | 94 |
| 类型： | 多压监控器 |
| 监视电压数目： | 3 |
| 输出： | 开路漏极，开路漏极 |
| 复位： | 高有效/低有效 |
| 复位超时： | 可调节/可选择 |
| 电压 - 阀值： | 1.75V，2.2V，2.95V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 16-SOIC |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
X40231, X40233, X40235, X40237, X40239
When the Block Lock bits of the CR register are set to
something other than BL1 = 0 and BL0 = 0, then the
“wiper position” of the DCPs cannot be changed - i.e.
DCP write operations cannot be conducted:
PUP1
0
0
PUP0
0
1
Power-on Reset delay (t PURESET )
50ms
100ms (Default)
BL1
0
BL0
0
DCP Write Operation Permissible
YES (Default)
1
1
0
1
200ms
300ms
0
1
1
1
0
1
NO
NO
NO
The default for these bits are PUP1 = 0, PUP0 = 1.
V2FS, V3FS: Voltage Monitor Status Bits (Volatile)
Bits V2FS and V3FS of the CR register are latched,
The factory default setting for these bits are BL1 = 0,
BL0 = 0.
IMPORTANT NOTE: If the Write Protect (WP) pin of
the X4023x is active (HIGH), then all nonvolatile write
operations to both the EEPROM memory and DCPs
are inhibited, irrespective of the Block Lock bit settings
(See "WP: Write Protection Pin").
volatile flag bits which indicate the status of the Volt-
age Monitor reset output pins V2FAIL and V3FAIL.
At power-up the VxFS (x=2,3) bits default to the value
“0”. These bits can be set to a “1” by writing the appro-
priate value to the CR register. To provide consistency
between the VxFAIL and V xFS however, the status of
the V xFS b its can only be set to a “1” when the corre-
sponding VxFAIL output is HIGH.
PUP1, PUP0: Power-on Reset bits – (Nonvolatile)
Applying voltage to V CC activates the Power-on Reset
circuit which holds RESET output HIGH, until the sup-
ply voltage stabilizes above the V TRIP1 threshold for a
period of time, t PURST (See Figure 30).
The Power-on Reset bits, PUP1 and PUP0 of the CR
register determine the t PURST delay time of the Power-
on Reset circuitry (See "VOLTAGE MONITORING
FUNCTIONS"). These bits of the CR register are non-
volatile, and therefore power-up to the last written
state.
The nominal Power-on Reset delay time can be
selected from the following table, by writing the appro-
priate bits to the CR register:
Once the VxFS bits have been set to “1”, they will be
reset to “0” if:
—The device is powered down, then back up,
—The corresponding V xFAIL output becomes LOW.
CR Register Write Operation
The CR register is accessed using the Slave Address
set to 1010010 (Refer to Figure 4). Following the
Slave Address Byte, access to the CR register
requires an Address Byte which must be set to FFh.
Only one data byte is allowed to be written for each
CR register Write operation. The user must issue a
STOP, after sending this byte to the register, to initiate
the nonvolatile cycle that stores the BP1, BP0, PUP1
and PUP0 bits. The X4023x will not ACKNOWLEDGE
any data bytes written after the first byte is entered
(Refer to Figure 18).
SCL
SDA
S
1
0
1
0
0
1
0
R/W A
1
1
1
1
1
1
1
1
A
CS7 CS6 CS5 CS4 CS3 CS2 CS1 CS0
A
S
T
A
R
T
SLAVE ADDRESS BYTE
C
K
ADDRESS BYTE
C
K
CR REGISTER DATA IN
C
K
T
O
P
Figure 18. CR Register Write Command Sequence
19
FN8115.0
April 11, 2005
相关PDF资料 |
PDF描述 |
|---|---|
| 450MXG390MEFCSN30X45 | CAP ALUM 390UF 450V 20% SNAP-IN |
| 0925-392K | COIL RF 3.9UH MOLDED SHIELDED |
| AYM12DTMD-S664 | CONN EDGECARD 24POS R/A .156 |
| ISL6554CBZ | IC PWM CORE VOLTAGE REG 20-SOIC |
| X40233S16I-BT1 | IC VOLTAGE MON TRPL EE 16-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| X40235S16I-AT1 | 功能描述:IC VOLTAGE MON TRPL EE 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X40235S16I-B | 功能描述:IC VOLTAGE MON TRPL EE 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X40235S16I-BT1 | 功能描述:IC VOLTAGE MON TRPL EE 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X40237 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Triple Voltage Monitors, POR, 2 kbit EEPROM MEMORY, and Single/Dual DCP |
| X40237S16I-A | 功能描述:IC VOLTAGE MON TRPL EE 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。