参数资料
| 型号： | X9118TV14-2.7 |
| 厂商： | Intersil |
| 文件页数： | 11/17页 |
| 文件大小： | 0K |
| 描述： | IC XDCP SGL 1024TAP 100K 14TSSOP |
| 标准包装： | 95 |
| 系列： | XDCP™ |
| 接片： | 1024 |
| 电阻（欧姆）： | 100k |
| 电路数： | 1 |
| 温度系数： | 标准值 ±300 ppm/°C |
| 存储器类型： | 非易失 |
| 接口： | I²C（设备位址） |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 14-TSSOP |
| 包装： | 管件 |
3
FN8161.4
December 4, 2009
Pin Configuration
X9118
(14 LD TSSOP)
TOP VIEW
Pin Descriptions
Bus Interface Pins
SERIAL DATA INPUT/OUTPUT (SDA)
The SDA is a bidirectional serial data input/output pin for a
2-wire slave device and is used to transfer data into and out
of the device. It receives device address, opcode, wiper
register address and data sent from a 2-wire master at the
rising edge of the serial clock SCL, and it shifts out data after
each falling edge of the serial clock SCL.
It is an open drain output and may be wire-ORed with any
number of open drain or open collector outputs. An open
drain output requires the use of a pull-up resistor. For
selecting typical values, refer to the guidelines for calculating
typical values on the bus pull-up resistors graph.
SERIAL CLOCK (SCL)
This input is used by 2-wire master to supply 2-wire serial
clock to the X9118.
DEVICE ADDRESS (A1–A0)
The address inputs are used to set the least significant 2 bits
of the 8-bit slave address. A match in the slave address
serial data stream must be made with the Address input in
order to initiate communication with the X9118. A maximum
of 4 XDCP devices may occupy the 2-wire serial bus.
HARDWARE WRITE PROTECT INPUT (WP)
The WP pin when LOW prevents nonvolatile writes to the
Data Registers.
Potentiometer Pins
RH, RL
The RH and RL pins are equivalent to the terminal
connections on a mechanical potentiometer.
RW
The wiper pin is equivalent to the wiper terminal of a
mechanical potentiometer.
Bias Supply Pins
SYSTEM SUPPLY VOLTAGE (VCC) AND SUPPLY
GROUND (VSS)
The VCC pin is the system or digital supply voltage. The VSS
pin is the system ground.
ANALOG SUPPLY VOLTAGES (V+ AND V
-)
These supplies are the analog voltage supplies for the
potentiometer. The V+ supply is tied to the wiper switches
while the V- supply is used to bias the switches and the
internal P+ substrate of the integrated circuit. Both of these
supplies set the voltage limits of the potentiometer.
Other Pins
NO CONNECT
No connect pins should be left open. These pins are used for
Intersil manufacturing and testing purposes.
Principles of Operation
The X9118 is an integrated microcircuit incorporating a
resistor array and its registers and counters and the serial
interface logic providing direct communication between the
host and the digitally controlled potentiometer. This section
provides a detailed description of the following:
Resistor Array Description
Serial Interface Description
Instruction and Register Description
Resistor Array Description
The X9118 is comprised of a resistor array. The array
contains 1023, in effect, discrete resistive segments that are
connected in series (see Figure 1). The physical ends of
each array are equivalent to the fixed terminals of a
mechanical potentiometer (RH and RL inputs).
Pin Assignments
PIN
(TSSOP)
SYMBOL
FUNCTION
1
V+
Analog Supply Voltage
2
NC
No Connect
3
A0
Device Address for 2-wire bus
4
SCL
Serial Clock for 2-wire bus
5WP
Hardware Write Protect
6
SDA
Serial Data Input/Output for 2-wire bus
7VSS
System Ground
8
V-
Analog Supply Voltage
9
A1
Device Address for 2-wire bus
10
NC
No Connect
11
RW
Wiper terminal of the Potentiometer
12
RH
High terminal of the Potentiometer
13
RL
Low terminal of the Potentiometer
14
VCC
System Supply Voltage
VCC
RL
VSS
1
2
3
4
5
6
7
8
14
13
12
11
10
9
A0
RW
SCL
A1
RH
NC
V+
SDA
NC
WP
V-
X9118
相关PDF资料 |
PDF描述 |
|---|---|
| VE-27X-MY-F2 | CONVERTER MOD DC/DC 5.2V 50W |
| V375A36T600BG | CONVERTER MOD DC/DC 36V 600W |
| VE-27X-MY-F1 | CONVERTER MOD DC/DC 5.2V 50W |
| M83723/95R1005N | CONN PLUG 5POS STRAIGHT W/SCKT |
| VE-26N-MW-S | CONVERTER MOD DC/DC 18.5V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| X9118TV14I | 功能描述:IC DCP 100K 1024TP 14TSSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:XDCP™ 标准包装:2,500 系列:XDCP™ 接片:256 电阻（欧姆）:100k 电路数:1 温度系数:标准值 ±300 ppm/°C 存储器类型:非易失 接口:I²C（设备位址） 电源电压:2.7 V ~ 5.5 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:带卷 (TR) |
| X9118TV14I-2.7 | 功能描述:IC XDCP SGL 1024TAP 100K 14TSSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:XDCP™ 标准包装:2,500 系列:XDCP™ 接片:256 电阻（欧姆）:100k 电路数:1 温度系数:标准值 ±300 ppm/°C 存储器类型:非易失 接口:I²C（设备位址） 电源电压:2.7 V ~ 5.5 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:带卷 (TR) |
| X9118TV14IZ | 功能描述:IC XDCP SGL 1024TAP 100K 14TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:XDCP™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 接片:256 电阻（欧姆）:100k 电路数:2 温度系数:标准值 35 ppm/°C 存储器类型:易失 接口:6 线串行（芯片选择，递增，增/减） 电源电压:2.6 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:带卷 (TR) |
| X9118TV14IZ-2.7 | 功能描述:IC XDCP SGL 1024TAP 100K 14TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:XDCP™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 接片:256 电阻（欧姆）:100k 电路数:2 温度系数:标准值 35 ppm/°C 存储器类型:易失 接口:6 线串行（芯片选择，递增，增/减） 电源电压:2.6 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:带卷 (TR) |
| X9118TV14Z | 功能描述:IC XDCP SGL 1024TAP 100K 14TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:XDCP™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 接片:256 电阻（欧姆）:100k 电路数:2 温度系数:标准值 35 ppm/°C 存储器类型:易失 接口:6 线串行（芯片选择，递增，增/减） 电源电压:2.6 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。