- 您现在的位置：买卖IC网 > PDF目录20009 > X9520V20I-B (Intersil)IC 3 DCP 2K EE LASR CTRL 20TSSOP PDF资料下载
参数资料
| 型号： | X9520V20I-B |
| 厂商： | Intersil |
| 文件页数： | 5/29页 |
| 文件大小： | 0K |
| 描述： | IC 3 DCP 2K EE LASR CTRL 20TSSOP |
| 标准包装： | 75 |
| 类型： | 激光二极管控制器（光纤） |
| 通道数： | 3 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 电流 - 电源： | 1.5mA |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 20-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 20-TSSOP |
| 包装： | 管件 |
| 安装类型： | 表面贴装 |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
X9520
SCL
from
SCL from
Master
Master
1
8
9
Data Output from
Transmitter
Data Output from
Receiver
START
FIGURE 3. ACKNOWLEDGE RESPONSE FROM RECEIVER
ACKNOWLEDGE
SERIAL ACKNOWLEDGE
An ACKNOWLEDGE (ACK) is a software convention used to
indicate a successful data transfer. The transmitting device,
either master or slave, will release the bus after transmitting
eight bits. During the ninth clock cycle, the receiver will pull the
SDA line LOW to ACKNOWLEDGE that it received the eight
bits of data. Refer to Figure 3.
The device will respond with an ACKNOWLEDGE after
recognition of a START condition if the correct Device
Identifier bits are contained in the Slave Address Byte. If a
write operation is selected, the device will respond with an
ACKNOWLEDGE after the receipt of each subsequent eight
bit word.
In the read mode, the device will transmit eight bits of data,
release the SDA line, then monitor the line for an
ACKNOWLEDGE. If an ACKNOWLEDGE is detected and
no STOP condition is generated by the master, the device
will continue to transmit data. The device will terminate
further data transmissions if an ACKNOWLEDGE is not
detected. The master must then issue a STOP condition to
place the device into a known state.
5
Device Internal Addressing
Addressing Protocol Overview
The user addressable internal components of the X9520 can
be split up into three main parts:
? Three Digitally Controlled Potentiometers (DCPs)
? EEPROM array
? Control and Status (CONSTAT) Register
Depending upon the operation to be performed on each of
these individual parts, a 1, 2 or 3 Byte protocol is used. All
operations however must begin with the Slave Address Byte
being issued on the SDA pin. The Slave address selects the
part of the X9520 to be addressed, and specifies if a Read or
Write operation is to be performed.
It should be noted that in order to perform a write operation
to either a DCP or the EEPROM array, the Write Enable
Latch (WEL) bit must first be set (See “BL1, BL0: Block Lock
protection bits - (Nonvolatile)” on page 13.)
Slave Address Byte
Following a START condition, the master must output a
Slave Address Byte (Refer to Figure 4). This byte consists of
three parts:
? The Device Type Identifier which consists of the most
significant four bits of the Slave Address (SA7 - SA4). The
Device Type Identifier must always be set to 1010 in order
to select the X9520.
? The next three bits (SA3 - SA1) are the Internal Device
Address bits. Setting these bits to 000 internally selects
the EEPROM array, while setting these bits to 111 selects
the DCP structures in the X9520. The CONSTAT Register
may be selected using the Internal Device Address 010.
? The Least Significant Bit of the Slave Address (SA0) Byte
is the R/W bit. This bit defines the operation to be
performed on the device being addressed (as defined in
the bits SA3 - SA1). When the R/W bit is “1”, then a READ
operation is selected. A “0” selects a WRITE operation
(Refer to Figure 4.)
FN8206.2
August 20, 2007
相关PDF资料 |
PDF描述 |
|---|---|
| VE-20V-CX | CONVERTER MOD DC/DC 5.8V 75W |
| CAT28F001HI-12T | IC FLASH MEM 1MBIT 120NS 32TSOP |
| ISL78302AARLLZ-T | IC REG LDO 2.9V .3A 10DFN |
| CAT28F020H90 | IC FLASH MEM 2MBIT 90NS 32TSOP |
| ACM43DRYF | CONN EDGECARD 86POS DIP .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| X9520V20I-BT1 | 功能描述:IC VOLT MON DUAL 2KBIT 20-TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 激光驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:60 系列:- 类型:激光二极管驱动器 数据速率:- 通道数:4 电源电压:3.3V 电流 - 电源:- 电流 - 调制:- 电流 - 偏置:- 工作温度:0°C ~ 70°C 封装/外壳:40-TQFN 裸露焊盘 供应商设备封装:40-TQFN EP 包装:托盘 安装类型:表面贴装 |
| X9520V20IZ-A | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Triple DCP, POR, 2kbit EEPROM Memory, Dual Voltage Monitors |
| X9520V20IZ-AT1 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Triple DCP, POR, 2kbit EEPROM Memory, Dual Voltage Monitors |
| X9520V20IZ-AT2 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Triple DCP, POR, 2kbit EEPROM Memory, Dual Voltage Monitors |
| X9520V20IZ-B | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Triple DCP, POR, 2kbit EEPROM Memory, Dual Voltage Monitors |
发布紧急采购，3分钟左右您将得到回复。