参数资料
| 型号： | X96010V14IZ |
| 厂商： | Intersil |
| 文件页数： | 18/26页 |
| 文件大小： | 0K |
| 描述： | IC SENSOR CONDITIONER 14-TSSOP |
| 标准包装： | 95 |
| 类型： | 传感器调节器 |
| 输入类型： | 电压 |
| 输出类型： | 电压 |
| 接口： | 2 线 |
| 电流 - 电源： | 15mA |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 14-TSSOP |
| 包装： | 管件 |
| 产品目录页面： | 1246 (CN2011-ZH PDF) |
25
FN8214.1
October 25, 2005
The Data Bytes are from the memory location indicated
by an internal pointer. This pointer initial value is deter-
mined by the Address Byte in the Read operation instruc-
tion, and increments by one during transmission of each
Data Byte. After reaching the memory location 10Fh, a
stop should be issued.
If the read operation continues, the output bytes are
unpredictable. If the address is set between 00h and
7Fh, the output bytes are unpredictable.
A Read operation internal pointer can start at any
memory location from 80h through FEh, when the
Address Byte is 80h through FEh respectively. But it
starts at location 100h if the Address Byte is FFh.
When reading any of the control registers 1, 2, 3, or 4,
the Data Bytes are always the content of the corre-
sponding nonvolatile cells, even if bit NV1234 is "0"
Data Protection
There are three levels of data protection designed into
the X96010: 1- Any Write to the device first requires
setting of the WEL bit in Control 6 register; 2- The
Write Protection pin disables any writing to the
X96010; 3- The proper clock count, data bit sequence,
and STOP condition is required in order to start a nonvol-
atile write cycle, otherwise the X96010 ignores the Write
operation.
WP: Write Protection Pin
When the Write Protection (WP) pin is active (LOW),
any Write operations to the X96010 is disabled, except
the writing of the WEL bit.
Signals
from the
Master
Signals from
the Slave
Signal at
SDA
S
t
a
r
t
Slave
Address
with
R/W = 0
Address
Byte
A
C
K
A
C
K
1
0
1
00
S
t
o
p
A
C
K
1
00
Slave
Address
with
R/W = 1
A
C
K
S
t
a
r
t
Last Read
Data Byte
First Read
Data Byte
A
C
K
Figure 21. Read Sequence
X96010
相关PDF资料 |
PDF描述 |
|---|---|
| X96012V14IZT1 | IC BIAS CTRLR UNIV SNSR 14-TSSOP |
| X9C303V8T2 | IC XDCP 100-TAP 32K EE 8-TSSOP |
| X9C503ST2 | IC XDCP 100-TAP 50K EE 8-SOIC |
| XA2C128-8CPG132Q | IC CPLD 128MC 100 I/O 132CSBGA |
| XA2C32A-7VQG44Q | IC CPLD 32MCELL 33 I/O 44-VQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| X96011 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Temperature Sensor with Look-Up Table Memory and DAC |
| X96011_08 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Temperature Sensor with Look-Up Table Memory and DAC |
| X96011V14I | 功能描述:CONDITIONER SGNL W/TABLE MEM&DAC RoHS:否 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
| X96011V14IZ | 功能描述:IC SENSOR TEMP BIAS SGL 14-TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
| X96012 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Universal Sensor Conditioner with Dual Look-up Table Memory and DACs |
发布紧急采购，3分钟左右您将得到回复。