参数资料
型号: XCS20-3PQ208I
厂商: Xilinx Inc
文件页数: 28/83页
文件大小: 0K
描述: IC FPGA 5V I-TEMP 208-PQFP
产品变化通告: Spartan,Virtex FPGA/SCD Discontinuation 18/Oct/2010
标准包装: 24
系列: Spartan®
LAB/CLB数: 400
逻辑元件/单元数: 950
RAM 位总计: 12800
输入/输出数: 160
门数: 20000
电源电压: 4.5 V ~ 5.5 V
安装类型: 表面贴装
工作温度: -40°C ~ 100°C
封装/外壳: 208-BFQFP
供应商设备封装: 208-PQFP(28x28)
Spartan and Spartan-XL FPGA Families Data Sheet
34
DS060 (v2.0) March 1, 2013
Product Specification
R
Product Obsolete/Under Obsolescence
Configuration Sequence
There are four major steps in the Spartan/XL FPGA
power-up configuration sequence.
Configuration Memory Clear
Initialization
Configuration
Start-up
The full process is illustrated in Figure 30.
Configuration Memory Clear
When power is first applied or is reapplied to an FPGA, an
internal circuit forces initialization of the configuration logic.
When VCC reaches an operational level, and the circuit
passes the write and read test of a sample pair of configu-
ration bits, a time delay is started. This time delay is nomi-
nally 16 ms. The delay is four times as long when in Master
Serial Mode to allow ample time for all slaves to reach a sta-
ble VCC. When all INIT pins are tied together, as recom-
mended, the longest delay takes precedence. Therefore,
devices with different time delays can easily be mixed and
matched in a daisy chain.
This delay is applied only on power-up. It is not applied
when reconfiguring an FPGA by pulsing the PROGRAM pin
Low. During this time delay, or as long as the PROGRAM
input is asserted, the configuration logic is held in a Config-
uration Memory Clear state. The configuration-memory
frames are consecutively initialized, using the internal oscil-
lator.
At the end of each complete pass through the frame
addressing, the power-on time-out delay circuitry and the
level of the PROGRAM pin are tested. If neither is asserted,
the logic initiates one additional clearing of the configuration
frames and then tests the INIT input.
Initialization
During initialization and configuration, user pins HDC, LDC,
INIT and DONE provide status outputs for the system inter-
face. The outputs LDC, INIT and DONE are held Low and
HDC is held High starting at the initial application of power.
The open drain INIT pin is released after the final initializa-
tion pass through the frame addresses. There is a deliber-
ate delay before a Master-mode device recognizes an
inactive INIT. Two internal clocks after the INIT pin is recog-
nized as High, the device samples the MODE pin to deter-
mine the configuration mode. The appropriate interface
lines become active and the configuration preamble and
data can be loaded.
Figure 29: Circuit for Generating CRC-16
0
X2
2
3456789 10 11 12 13 14
1
X15
X16
15
SERIAL DATA IN
1
0 1514 13 12 1110 9
8
7
65
1
CRC – CHECKSUM
LAST DATA FRAME
START
BIT
DS060_29_080400
Polynomial: X16 + X15 + X2 + 1
Readback Data Stream
相关PDF资料
PDF描述
XCS10XL-4VQ100I IC FPGA 3.3V I-TEMP 100-VQFP
KMPC860DEVR80D4 IC MPU POWERQUICC 80MHZ 357-PBGA
FMC65DRAH CONN EDGECARD 130PS R/A .100 SLD
FMC50DREN-S13 CONN EDGECARD 100POS .100 EXTEND
FMC50DREH-S13 CONN EDGECARD 100POS .100 EXTEND
相关代理商/技术参数
参数描述
XCS20-3PQ240C 制造商:XILINX 制造商全称:XILINX 功能描述:Spartan and Spartan-XL Families Field Programmable Gate Arrays
XCS20-3PQ240I 制造商:XILINX 制造商全称:XILINX 功能描述:Spartan and Spartan-XL FPGA
XCS20-3PQ256C 制造商:XILINX 制造商全称:XILINX 功能描述:Spartan and Spartan-XL Families Field Programmable Gate Arrays
XCS20-3PQ256I 制造商:XILINX 制造商全称:XILINX 功能描述:Spartan and Spartan-XL Families Field Programmable Gate Arrays
XCS20-3PQ280C 制造商:XILINX 制造商全称:XILINX 功能描述:Spartan and Spartan-XL Families Field Programmable Gate Arrays