- 您现在的位置：买卖IC网 > PDF目录300150 > XCS40XL-5PQ208C (XILINX INC) Spartan and Spartan-XL Families Field Programmable Gate Arrays PDF资料下载
参数资料
| 型号： | XCS40XL-5PQ208C |
| 厂商： | XILINX INC |
| 元件分类： | FPGA |
| 英文描述： | Spartan and Spartan-XL Families Field Programmable Gate Arrays |
| 中文描述： | FPGA, 784 CLBS, 13000 GATES, 250 MHz, PQFP208 |
| 封装： | PLASTIC, QFP-208 |
| 文件页数： | 20/83页 |
| 文件大小： | 770K |
| 代理商： | XCS40XL-5PQ208C |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页
Spartan and Spartan-XL FPGA Families Data Sheet
DS060 (v1.8) June 26, 2008
27
Product Specification
R
Master Serial Mode
The Master serial mode uses an internal oscillator to gener-
ate a Configuration Clock (CCLK) for driving potential slave
devices
and
the
Xilinx
serial-configuration
PROM
(SPROM). The CCLK speed is selectable as either 1 MHz
(default) or 8 MHz. Configuration always starts at the default
slow frequency, then can switch to the higher frequency dur-
ing the first frame. Frequency tolerance is –50% to +25%.
In Master Serial mode, the CCLK output of the device drives
a Xilinx SPROM that feeds the FPGA DIN input. Each rising
edge of the CCLK output increments the Serial PROM inter-
nal address counter. The next data bit is put on the SPROM
data output, connected to the FPGA DIN pin. The FPGA
accepts this data on the subsequent rising CCLK edge.
When used in a daisy-chain configuration the Master Serial
FPGA is placed as the first device in the chain and is
referred to as the lead FPGA. The lead FPGA presents the
preamble data, and all data that overflows the lead device,
on its DOUT pin. There is an internal pipeline delay of 1.5
CCLK periods, which means that DOUT changes on the
falling CCLK edge, and the next FPGA in the daisy chain
accepts data on the subsequent rising CCLK edge. See the
timing diagram in Figure 24.
In the bitstream generation software, the user can specify
Fast Configuration Rate, which, starting several bits into the
first frame, increases the CCLK frequency by a factor of
eight. For actual timing values please refer to the specifica-
tion section. Be sure that the serial PROM and slaves are
fast enough to support this data rate. Earlier families such
as the XC3000 series do not support the Fast Configuration
Rate option.
The SPROM CE input can be driven from either LDC or
DONE. Using LDC avoids potential contention on the DIN
pin, if this pin is configured as user I/O, but LDC is then
restricted to be a permanently High user output after config-
uration. Using DONE can also avoid contention on DIN, pro-
vided the Early DONE option is invoked.
Figure 25 shows a full master/slave system. The leftmost
device is in Master Serial mode, all other devices in the
chain are in Slave Serial mode.
Slave Serial Mode
In Slave Serial mode, the FPGA receives serial configura-
tion data on the rising edge of CCLK and, after loading its
configuration, passes additional data out, resynchronized
on the next falling edge of CCLK.
In this mode, an external signal drives the CCLK input of the
FPGA (most often from a Master Serial device). The serial
configuration bitstream must be available at the DIN input of
the lead FPGA a short setup time before each rising CCLK
edge.
The lead FPGA then presents the preamble data—and all
data that overflows the lead device—on its DOUT pin. There
is an internal delay of 0.5 CCLK periods, which means that
DOUT changes on the falling CCLK edge, and the next
FPGA in the daisy chain accepts data on the subsequent
rising CCLK edge.
Figure 25 shows a full master/slave system. A Spartan/XL
device in Slave Serial mode should be connected as shown
in the third device from the left.
Figure 24: Master Serial Mode Programming Switching Characteristics
Serial Data In
CCLK
(Output)
Serial DOUT
(Output)
TDSCK
n
n + 1
n + 2
n – 3
n – 2
n – 1
n
TCKDS
DS060_24_080400
Notes:
1.
At power-up, VCC must rise from 2.0V to VCC min in less than 25 ms, otherwise
delay configuration by pulling PROGRAM Low until VCC is valid.
2.
Master Serial mode timing is based on testing in slave mode.
Symbol
Description
Min
Units
CCLK
TDSCK
DIN setup
20
ns
TCKDS
DIN hold
0
ns
相关PDF资料 |
PDF描述 |
|---|---|
| XCS40XL-5PQ240C | Spartan and Spartan-XL Families Field Programmable Gate Arrays |
| XCS10XL-5CS144C | Spartan and Spartan-XL Families Field Programmable Gate Arrays |
| XCS10XL-5PC84C | Spartan and Spartan-XL Families Field Programmable Gate Arrays |
| XCS10XL-5TQ144C | Spartan and Spartan-XL Families Field Programmable Gate Arrays |
| XCS20-4PQ208C | Spartan and Spartan-XL Families Field Programmable Gate Arrays |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XCS40XL-5PQ208I | 制造商:XILINX 制造商全称:XILINX 功能描述:Spartan and Spartan-XL FPGA |
| XCS40XL-5PQ240C | 功能描述:IC FPGA 3.3V C-TEMP 240-PQFP RoHS:否 类别:集成电路 (IC) >> 嵌入式 - FPGA（现场可编程门阵列） 系列:Spartan®-XL 标准包装:1 系列:Kintex-7 LAB/CLB数:25475 逻辑元件/单元数:326080 RAM 位总计:16404480 输入/输出数:350 门数:- 电源电压:0.97 V ~ 1.03 V 安装类型:表面贴装 工作温度:0°C ~ 85°C 封装/外壳:900-BBGA，FCBGA 供应商设备封装:900-FCBGA（31x31） 其它名称:122-1789 |
| XCS40XL-5PQ240I | 制造商:XILINX 制造商全称:XILINX 功能描述:Spartan and Spartan-XL FPGA |
| XCS40XL-5PQ256C | 制造商:XILINX 制造商全称:XILINX 功能描述:Spartan and Spartan-XL Families Field Programmable Gate Arrays |
| XCS40XL-5PQ256I | 制造商:XILINX 制造商全称:XILINX 功能描述:Spartan and Spartan-XL Families Field Programmable Gate Arrays |
发布紧急采购，3分钟左右您将得到回复。