参数资料
| 型号： | XE8806AMI026TLF |
| 厂商： | Semtech |
| 文件页数： | 76/143页 |
| 文件大小： | 0K |
| 描述： | IC MCU LOW PWR MTP FLASH 32-TQFP |
| 标准包装： | 1 |
| 系列： | XE880x |
| 应用： | 感测机 |
| 核心处理器： | Coolrisc816? |
| 程序存储器类型： | 闪存（22 kB） |
| 控制器系列： | XE8000 |
| RAM 容量： | 512 x 8 |
| 接口： | UART，USRT |
| 输入/输出数： | 24 |
| 电源电压： | 2.4 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-TQFP |
| 包装： | 剪切带 (CT) |
| 供应商设备封装： | 32-TQFP（7x7） |
| 配用： | XE8000MP-ND - PROG BOARD AND PROSTART2 CARD |
| 其它名称： | XE8806AMI026CT |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页当前第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页
Semtech 2006
www.semtech.com
6-5
XE8806A/XE8807A
6.5.5
BusError reset
The address space is assigned as shown in the register map of the product. If the EnBusError bit in the
RegSysCtrl register is set and the software accesses an unused address, a reset is generated.
6.6
Sleep mode
Entering the sleep mode will reset a part of the circuit. The reset is used to configure the circuit for correct wake-up
after the sleep mode. If the SleepEn bit in the RegSysCtrl register has been set, the sleep mode can be entered
by setting the bit Sleep in RegSysReset. During the sleep mode, the nresetsleep signal is active. For detailed
information on the sleep mode, see the system documentation.
6.7
Control register description and operation
Two registers are dedicated for reset status and control, RegSysReset and RegSysCtrl. The bits Sleep,
SleepFlag and SleepEn are also located in those registers and are described in the chapter dedicated to the
different operating modes of the circuit (system block).
The RegSysReset register gives information on the source that generated the last reset. It can be read at the
beginning of the application program to detect if the circuit is recovering from an error or exception condition, or if
the circuit is starting up normally.
when ResetBusError is 1, a forbidden address access generated the reset.
when ResetWD is 1, the watchdog generated the reset.
when ResetfromPortA is 1, a PortA combination generated the reset.
Note: If no bit is set to 1, the reset source was either the NRESET pin or the internal POR.
Note: Several bits might be set or not, if the register was not cleared in between 2 reset occurrences.
The two other bits concern the sleep mode control and information (see system documentation for the sleep mode
description).
When SleepFlag is 1, the sleep mode was active before the reset occurred. This bit will always appear
together with the ResetfromPortA bit since all other possibilities to leave the sleep mode (POR and
NRESET pin) will clear the SleepFlag.
When Sleep is set to 1, and SleepEn is 1, the sleep mode is entered. The bit always reads back a 0.
The RegSysCtrl register enables the different available reset sources and the sleep mode.
EnBusError enables the reset due to a bus error condition.
EnResetWD enables the reset due to the watchdog (can not be disabled once enabled).
EnResetPConf enables the reset of the port configurations when reset by Port A, a Bus Error or the
watchdog.
SleepEn unlocks the Sleep bit. As long as SleepEn is 0, the Sleep bit has no effect.
6.8
Watchdog
The watchdog is a timer, which has to be cleared at least every 2 seconds by the software to prevent a reset to be
generated by the timeout condition.
The watchdog can be enabled by software by setting the EnResetWD bit in the RegSysCtrl register to 1. It can
then only be disabled by a power on reset or by setting the NRESET pin to a low state.
The watchdog timer can be cleared by writing consecutively the values Hx0A and Hx03 to the RegSysWd register.
The sequence must strictly be respected to clear the watchdog.
相关PDF资料 |
PDF描述 |
|---|---|
| 395-026-540-804 | CARD EDGE 26POS DL .100X.200 BLK |
| DS1270Y-100# | IC NVSRAM 16MBIT 100NS 36DIP |
| DS1270W-150# | IC NVSRAM 16MBIT 150NS 36DIP |
| DS1270W-100# | IC NVSRAM 16MBIT 100NS 36DIP |
| AYF337365 | CONN FPC 73POS SMD Y3BW |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XE8806ARI000 | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:Ultra Low-Power Low-Voltage |
| XE8806ARI026LF | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:Ultra Low-Power Low-Voltage |
| XE8807AMI000 | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:Ultra Low-Power Low-Voltage |
| XE8807AMI026LF | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:Ultra Low-Power Low-Voltage |
| XE8807AMI026TLF | 功能描述:IC MCU LOW PWR MTP FLASH 32-TQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器 - 特定应用 系列:XE880x 产品变化通告:Product Discontinuation 26/Aug/2009 标准包装:250 系列:- 应用:网络处理器 核心处理器:4Kc 程序存储器类型:- 控制器系列:- RAM 容量:16K x 8 接口:以太网，UART，USB 输入/输出数:- 电源电压:1.8V, 3.3V 工作温度:- 安装类型:表面贴装 封装/外壳:208-LQFP 包装:带卷 (TR) 供应商设备封装:PG-LQFP-208 其它名称:SP000314382 |
发布紧急采购，3分钟左右您将得到回复。