参数资料
| 型号： | XR16L2752CJTR-F |
| 厂商： | Exar Corporation |
| 文件页数： | 19/49页 |
| 文件大小： | 0K |
| 描述： | IC UART FIFO 64B DUAL 44PLCC |
| 标准包装： | 500 |
| 特点： | * |
| 通道数： | 2，DUART |
| FIFO's： | 64 字节 |
| 规程： | RS232，RS485 |
| 电源电压： | 2.25 V ~ 5.5 V |
| 带自动流量控制功能： | 是 |
| 带IrDA 编码器/解码器： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 44-LCC（J 形引线） |
| 供应商设备封装： | 44-PLCC（16.59x16.59） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页
XR16L2752
xr
2.25V TO 5.5V DUART WITH 64-BYTE FIFO
REV. 1.2.1
26
FCR[2]: TX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
Logic 0 = No transmit FIFO reset (default).
Logic 1 = Reset the transmit FIFO pointers and FIFO level counter logic (the transmit shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
FCR[3]: DMA Mode Select
Controls the behavior of the TXRDY# and RXRDY# pins. See DMA operation section for details.
Logic 0 = Normal Operation (default).
Logic 1 = DMA Mode.
FCR[5:4]: Transmit FIFO Trigger Select
(logic 0 = default, TX trigger level = one)
These 2 bits set the trigger level for the transmit FIFO. The UART will issue a transmit interrupt when the
number of characters in the FIFO falls below the selected trigger level, or when it gets empty in case that the
FIFO did not get filled over the trigger level on last re-load. Table 10 below shows the selections. EFR bit-4
must be set to ‘1’ before these bits can be accessed. Note that the receiver and the transmitter cannot use
different trigger tables. Whichever selection is made last applies to both the RX and TX side.
FCR[7:6]: Receive FIFO Trigger Select
(logic 0 = default, RX trigger level =1)
The FCTR Bits 5-4 are associated with these 2 bits. These 2 bits are used to set the trigger level for the receive
FIFO. The UART will issue a receive interrupt when the number of the characters in the FIFO crosses the
trigger level. Table 10 shows the complete selections. Note that the receiver and the transmitter cannot use
different trigger tables. Whichever selection is made last applies to both the RX and TX side.
相关PDF资料 |
PDF描述 |
|---|---|
| ST16C650AIQ48TR-F | IC UART FIFO 32B 48TQFP |
| ST16C552ACJ68TR-F | IC UART FIFO 16B DUAL 68PLCC |
| ST16C650ACJ44TR-F | IC UART FIFO 32B 44PLCC |
| XR16V2552IL-F | IC UART FIFO 16B DUAL 32QFN |
| XR16L2552IM-F | IC UART FIFO 16B DUAL 48TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR16L2752IJ | 制造商:EXAR 制造商全称:EXAR 功能描述:2.25V TO 5.5V DUART WITH 64-BYTE FIFO |
| XR16L2752IJ-F | 功能描述:UART 接口集成电路 UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR16L2752IJTR-F | 制造商:Exar Corporation 功能描述:XR16L2752 Series 6.25 Mbps 5.5 V Dual UART With 64-Byte FIFO - PLCC-44 |
| XR16L570 | 制造商:EXAR 制造商全称:EXAR 功能描述:SMALLEST 1.62V TO 5.5V UART WITH 16-BYTE FIFO AND POWERSAVE |
| XR16L570_07 | 制造商:EXAR 制造商全称:EXAR 功能描述:SMALLEST 1.62V TO 5.5V UART WITH 16-BYTE FIFO AND POWERSAVE |
发布紧急采购，3分钟左右您将得到回复。