- 您现在的位置：买卖IC网 > PDF目录16507 > XR16M554IJ-0B-EVB (Exar Corporation)EVAL BOARD FOR XR16M554-B 68PLCC PDF资料下载
参数资料
| 型号： | XR16M554IJ-0B-EVB |
| 厂商： | Exar Corporation |
| 文件页数： | 5/46页 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD FOR XR16M554-B 68PLCC |
| 标准包装： | 1 |
| 系列： | * |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页
XR16M554/554D
13
REV. 1.0.0
1.62V TO 3.63V QUAD UART WITH 16-BYTE FIFO
2.7
Crystal Oscillator or External Clock Input
The M554 includes an on-chip oscillator (XTAL1 and XTAL2) to produce a clock for both UART sections in the
device. The CPU data bus does not require this clock for bus operation. The crystal oscillator provides a
system clock to the Baud Rate Generators (BRG) section found in each of the UART. XTAL1 is the input to the
oscillator or external clock buffer input with XTAL2 pin being the output. For programming details, see
The on-chip oscillator is designed to use an industry standard microprocessor crystal (parallel resonant,
fundamental frequency with 10-22 pF capacitance load, ESR of 20-120 ohms and 100ppm frequency
tolerance) connected externally between the XTAL1 and XTAL2 pins. Typical oscillator connections are shown
in Figure 5. Alternatively, an external clock can be connected to the XTAL1 pin to clock the internal baud rate
generator for standard or custom rates. For further reading on oscillator circuit please see application note
DAN108 on EXAR’s web site.
2.8
Programmable Baud Rate Generator
Each UART has its own Baud Rate Generator (BRG) for the transmitter and receiver. The BRG further divides
this clock by a programmable divisor between 1 and (216 - 0.0625) in increments of 0.0625 (1/16) to obtain a
16X sampling rate clock of the serial data rate. The sampling rate clock is used by the transmitter for data bit
shifting and receiver for data sampling. The BRG divisor defaults to the maximum baud rate (DLL = 0x01 and
DLM = 0x00) upon power up and reset. Programming the Baud Rate Generator Registers DLL and DLM
provides the capability for selecting the operating data rate. Table 6 shows the standard data rates available
with a 24MHz crystal or external clock at 16X clock rate. If the pre-scaler is used (MCR bit-7 = 1), the output
data rate will be 4 times less than that shown in Table 6.
TABLE 5: TXRDY# AND RXRDY# OUTPUTS IN FIFO AND DMA MODE FOR CHANNELS A-D
PINS
FCR BIT-0=0
(FIFO DISABLED)
FCR BIT-0=1 (FIFO ENABLED)
FCR BIT-3 = 0
(DMA MODE DISABLED)
FCR BIT-3 = 1
(DMA MODE ENABLED)
RXRDY#
LOW = 1 byte
HIGH = no data
LOW = at least 1 byte in FIFO
HIGH = FIFO empty
HIGH to LOW transition when FIFO reaches the
trigger level, or timeout occurs
LOW to HIGH transition when FIFO empties
TXRDY#
LOW = THR empty
HIGH = byte in THR
LOW = FIFO empty
HIGH = at least 1 byte in FIFO
LOW = FIFO has at least 1 empty location
HIGH = FIFO is full
FIGURE 5. TYPICAL CRYSTAL CONNECTIONS
C1
22-47pF
C2
22-47pF
14.7456
MHz
XTAL1
XTAL2
R=300K to 400K
相关PDF资料 |
PDF描述 |
|---|---|
| M1AXK-1640K | IDC CABLE - MSC16K/MC16F/X |
| XR16M554IJ-0A-EVB | EVAL BOARD FOR XR16M554-A 68PLCC |
| VI-2TL-EX | CONVERTER MOD DC/DC 28V 75W |
| 6278879-3 | C/A 50/125UM RIS MTRJ 3M1 |
| H3DKH-4036G | IDC CABLE - HKR40H/AE40G/HPK40H |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR16M554IJ68 | 制造商:EXAR 制造商全称:EXAR 功能描述:1.62V TO 3.63V QUAD UART WITH 16-BYTE FIFO |
| XR16M554IJ68-F | 功能描述:UART 接口集成电路 UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR16M554IL-0A-EVB | 功能描述:界面开发工具 Eval Board for XR16M554IL-0A RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| XR16M554IL-0B-EVB | 功能描述:界面开发工具 Eval Board for XR16M554IL-0B RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| XR16M554IL48 | 制造商:EXAR 制造商全称:EXAR 功能描述:1.62V TO 3.63V QUAD UART WITH 16-BYTE FIFO |
发布紧急采购，3分钟左右您将得到回复。