- 您现在的位置：买卖IC网 > PDF目录11834 > XR16M554IL48-F (Exar Corporation)IC UART FIFO 16B QUAD 48QFN PDF资料下载
参数资料
| 型号： | XR16M554IL48-F |
| 厂商： | Exar Corporation |
| 文件页数： | 16/46页 |
| 文件大小： | 0K |
| 描述： | IC UART FIFO 16B QUAD 48QFN |
| 标准包装： | 260 |
| 特点： | * |
| 通道数： | 4，QUART |
| FIFO's： | 16 字节 |
| 规程： | RS232 |
| 电源电压： | 1.62 V ~ 3.63 V |
| 带自动流量控制功能： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-VFQFN 裸露焊盘 |
| 供应商设备封装： | 48-QFN-EP（7x7） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页
XR16M554/554D
23
REV. 1.0.0
1.62V TO 3.63V QUAD UART WITH 16-BYTE FIFO
ISR[7:6]: FIFO Enable Status
These bits are set to a logic 0 when the FIFOs are disabled. They are set to a logic 1 when the FIFOs are
enabled.
4.5
FIFO Control Register (FCR) - Write-Only
This register is used to enable the FIFOs, clear the FIFOs, set the receive FIFO trigger levels, and select the
DMA mode. The DMA, and FIFO modes are defined as follows:
FCR[0]: TX and RX FIFO Enable
Logic 0 = Disable the transmit and receive FIFO (default).
Logic 1 = Enable the transmit and receive FIFOs. This bit must be set to logic 1 when other FCR bits are
written or they will not be programmed.
FCR[1]: RX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
Logic 0 = No receive FIFO reset (default).
Logic 1 = Reset the receive FIFO pointers and FIFO level counter logic (the receive shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
FCR[2]: TX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
Logic 0 = No transmit FIFO reset (default).
Logic 1 = Reset the transmit FIFO pointers and FIFO level counter logic (the transmit shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
FCR[3]: DMA Mode Select
Controls the behavior of the TXRDY and RXRDY pins. See DMA operation section for details.
Logic 0 = Normal Operation (default).
Logic 1 = DMA Mode.
FCR[5:4]: Reserved (Default 0)
FCR[7:6]: Receive FIFO Trigger Select
(logic 0 = default, RX trigger level =1)
These 2 bits are used to set the trigger level for the receive FIFO. The UART will issue a receive interrupt when
the number of the characters in the FIFO crosses the trigger level. Table 10 shows the complete selections.
TABLE 10: RECEIVE FIFO TRIGGER LEVEL SELECTION
FCR BIT-7
FCR BIT-6
RECEIVE TRIGGER LEVEL
0
1
0
1
0
1
4
8
14
相关PDF资料 |
PDF描述 |
|---|---|
| MS27484T12A35S | CONN PLUG 22POS STRAIGHT W/SCKT |
| XR88C92CV-F | IC UART FIFO DUAL 44LQFP |
| D38999/20WC98S | CONN RCPT 10POS WALL MNT W/SCKT |
| XR88C681J-F | IC UART CMOS DUAL 44PLCC |
| ST16C552AIJ68-F | IC UART FIFO 16B DUAL 68PLCC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR16M554IV-0A-EVB | 功能描述:界面开发工具 Eval Board for XR16M554IV-0A RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| XR16M554IV-0B-EVB | 功能描述:界面开发工具 Eval Board for XR16M554IV-0B RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| XR16M554IV64 | 制造商:EXAR 制造商全称:EXAR 功能描述:1.62V TO 3.63V QUAD UART WITH 16-BYTE FIFO |
| XR16M554IV64-F | 功能描述:UART 接口集成电路 1.62V-3.63V QUAD UART W/ 16BYTE FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR16M554IV80 | 制造商:EXAR 制造商全称:EXAR 功能描述:1.62V TO 3.63V QUAD UART WITH 16-BYTE FIFO |
发布紧急采购，3分钟左右您将得到回复。