参数资料
| 型号： | XR16M670IL32-F |
| 厂商： | Exar Corporation |
| 文件页数： | 22/50页 |
| 文件大小： | 0K |
| 描述： | IC UART FIFO 32B 32QFN |
| 标准包装： | 490 |
| 特点： | * |
| 通道数： | 1，UART |
| FIFO's： | 32 字节 |
| 规程： | RS232，RS422，RS485 |
| 电源电压： | 1.62 V ~ 3.63 V |
| 带自动流量控制功能： | 是 |
| 带IrDA 编码器/解码器： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN 裸露焊盘（5x5） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页
XR16M670
29
REV. 1.0.1
1.62V TO 3.63V HIGH PERFORMANCE UART WITH 32-BYTE FIFO
4.5
FIFO Control Register (FCR) - Write-Only
This register is used to enable the FIFOs, clear the FIFOs, set the transmit/receive FIFO trigger levels, and
enable the wake up interrupt. They are defined as follows:
FCR[0]: TX and RX FIFO Enable
Logic 0 = Disable the transmit and receive FIFO (default).
Logic 1 = Enable the transmit and receive FIFOs. This bit must be set to logic 1 when other FCR bits are
written or they will not be programmed.
FCR[1]: RX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
Logic 0 = No receive FIFO reset (default)
Logic 1 = Reset the receive FIFO pointers and FIFO level counter logic (the receive shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
FCR[2]: TX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
Logic 0 = No transmit FIFO reset (default).
Logic 1 = Reset the transmit FIFO pointers and FIFO level counter logic (the transmit shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
FCR[3]: Enable wake up interrupt (requires EFR bit-4 = 1)
Logic 0 = Disable the wake up interrupt (default).
Logic 1 = Enable the wake up interrupt.
Please refer to “Section 2.17.3, Wake-up Interrupt” on page 21.
FCR[5:4]: Transmit FIFO Trigger Select (requires EFR bit-4 = 1)
These 2 bits set the trigger level for the transmit FIFO. The UART will issue a transmit interrupt when the
number of characters in the FIFO falls below the selected trigger level, or when it gets empty in case that the
FIFO did not get filled over the trigger level on last re-load. Table 9 below shows the selections. Note that the
receiver and the transmitter cannot use different trigger tables. Whichever selection is made last applies to
both the RX and TX side.
FCR[7:6]: Receive FIFO Trigger Select
These 2 bits are used to set the trigger level for the receive FIFO. The UART will issue a receive interrupt when
the number of the characters in the FIFO crosses the trigger level. Table 9 shows the complete selections.
Note that the receiver and the transmitter cannot use different trigger tables. Whichever selection is made last
applies to both the RX and TX side.
相关PDF资料 |
PDF描述 |
|---|---|
| XR16M680IM48-F | IC UART FIFO 32B 48TQFP |
| XR16M681IL32-F | IC UART FIFO 64B 32QFN |
| XR16M698IQ100-F | IC UART FIFO 32B OCTAL 100QFP |
| XR16M770IL32-F | IC UART FIFO 64B 32QFN |
| XR16M780IM48-F | IC UART FIFO 64B 48TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR16M670IL32TR-F | 制造商:Exar Corporation 功能描述:UART 1-CH 32Byte FIFO 1.8V/2.5V/3.3V 32-Pin QFN EP T/R 制造商:Exar Corporation 功能描述:XR16M670IL32TR-F |
| XR16M680 | 制造商:EXAR 制造商全称:EXAR 功能描述:1.62V TO 3.63V HIGH PERFORMANCE UART WITH 32-BYTE FIFO |
| XR16M680IB25 | 制造商:EXAR 制造商全称:EXAR 功能描述:1.62V TO 3.63V HIGH PERFORMANCE UART WITH 32-BYTE FIFO |
| XR16M680IB25-0C-EB | 功能描述:界面开发工具 Eval Board for XR16M680IB25 Series RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| XR16M680IB25-F | 功能描述:UART 接口集成电路 1.8 HIGH PERFORMANCE UART W/32 RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。