参数资料
型号: XR16M670IL32-F
厂商: Exar Corporation
文件页数: 23/50页
文件大小: 0K
描述: IC UART FIFO 32B 32QFN
标准包装: 490
特点: *
通道数: 1,UART
FIFO's: 32 字节
规程: RS232,RS422,RS485
电源电压: 1.62 V ~ 3.63 V
带自动流量控制功能:
带IrDA 编码器/解码器:
带故障启动位检测功能:
带调制解调器控制功能:
带CMOS:
安装类型: 表面贴装
封装/外壳: 32-VFQFN 裸露焊盘
供应商设备封装: 32-QFN 裸露焊盘(5x5)
包装: 托盘
XR16M670
3
REV. 1.0.1
1.62V TO 3.63V HIGH PERFORMANCE UART WITH 32-BYTE FIFO
PIN DESCRIPTIONS
Pin Description
NAME
24-QFN
PIN#
32-QFN
PIN#
25-BGA
PIN#
TYPE
DESCRIPTION
DATA BUS INTERFACE
A2
A1
A0
12
13
14
17
18
19
A5
A4
B4
I
Address lines [2:0]. These 3 address lines select the internal regis-
ters in UART during a data bus transaction.
D7
D6
D5
D4
D3
D2
D1
D0
3
2
1
24
23
22
21
20
5
4
3
1
32
31
30
29
C3
C2
E3
E1
D1
E2
D2
C1
I/O
Data bus lines [7:0] (bidirectional).
IOR#
11
14
B5
I
This input is read strobe (active low). The falling edge instigates an
internal read cycle and retrieves the data byte from an internal reg-
ister pointed by the address lines [A2:A0], puts the data byte on the
data bus to allow the host processor to read it on the rising edge.
IOW#
9
12
C5
I
This input is write strobe (active low). The falling edge instigates the
internal write cycle and the rising edge transfers the data byte on
the data bus to an internal register pointed by the address lines.
CS#
6
8
D4
I
This input is chip select (active low) to enable the device.
INT
15
20
A3
O
This output is the active high device interrupt output. The output
state is defined by the user through the software setting of MCR[3].
INT is set to the active mode when MCR[3] is set to a logic 1. INT is
set to the three state mode when MCR[3] is set to a logic 0. See
MCR[3].
MODEM OR SERIAL I/O INTERFACE
TX
5
7
D3
O
UART Transmit Data or infrared encoder data. Standard transmit
and receive interface is enabled when MCR[6] = 0. In this mode,
the TX signal will be a logic 1 during reset or idle (no data). Infrared
IrDA transmit and receive interface is enabled when MCR[6] = 1. In
the Infrared mode, the inactive state (no data) for the Infrared
encoder/decoder interface is a logic 0. If it is not used, leave it
unconnected.
RX
4
6
E4
I
UART Receive Data or infrared receive data. Normal receive data
input must idle at logic 1 condition. The infrared receiver idles at
logic 0. This input should be connected to VCC when not used.
RTS#
16
21
B3
O
UART Request-to-Send (active low) or general purpose output.
This output must be asserted prior to using auto RTS flow control,
see EFR[6], MCR[1] and IER[6].
CTS#
18
24
A1
I
UART Clear-to-Send (active low) or general purpose input. It can
be used for auto CTS flow control, see EFR[7], MSR[4] and IER[7].
This input should be connected to VCC when not used.
DTR#
-
22
B2
O
UART Data-Terminal-Ready (active low) or general purpose output.
相关PDF资料
PDF描述
XR16M680IM48-F IC UART FIFO 32B 48TQFP
XR16M681IL32-F IC UART FIFO 64B 32QFN
XR16M698IQ100-F IC UART FIFO 32B OCTAL 100QFP
XR16M770IL32-F IC UART FIFO 64B 32QFN
XR16M780IM48-F IC UART FIFO 64B 48TQFP
相关代理商/技术参数
参数描述
XR16M670IL32TR-F 制造商:Exar Corporation 功能描述:UART 1-CH 32Byte FIFO 1.8V/2.5V/3.3V 32-Pin QFN EP T/R 制造商:Exar Corporation 功能描述:XR16M670IL32TR-F
XR16M680 制造商:EXAR 制造商全称:EXAR 功能描述:1.62V TO 3.63V HIGH PERFORMANCE UART WITH 32-BYTE FIFO
XR16M680IB25 制造商:EXAR 制造商全称:EXAR 功能描述:1.62V TO 3.63V HIGH PERFORMANCE UART WITH 32-BYTE FIFO
XR16M680IB25-0C-EB 功能描述:界面开发工具 Eval Board for XR16M680IB25 Series RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V
XR16M680IB25-F 功能描述:UART 接口集成电路 1.8 HIGH PERFORMANCE UART W/32 RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel