参数资料
| 型号： | XR16V554IVTR-F |
| 厂商： | Exar Corporation |
| 文件页数： | 18/43页 |
| 文件大小： | 0K |
| 描述： | IC UART FIFO 16B QUAD 64LQFP |
| 标准包装： | 1,000 |
| 特点： | * |
| 通道数： | 4，QUART |
| FIFO's： | 16 字节 |
| 规程： | RS232 |
| 电源电压： | 2.25 V ~ 3.6 V |
| 带自动流量控制功能： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-LQFP |
| 供应商设备封装： | 64-LQFP（10x10） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页
XR16V554/554D
25
REV. 1.0.3
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
LCR[5]: TX and RX Parity Select
If the parity bit is enabled, LCR BIT-5 selects the forced parity format.
LCR BIT-5 = logic 0, parity is not forced (default).
LCR BIT-5 = logic 1 and LCR BIT-4 = logic 0, parity bit is forced to HIGH for the transmit and receive data.
LCR BIT-5 = logic 1 and LCR BIT-4 = logic 1, parity bit is forced to LOW for the transmit and receive data.
TABLE 11: PARITY SELECTION
LCR BIT-5 LCR BIT-4 LCR BIT-3
PARITY SELECTION
X
0
No parity
0
1
Odd parity
0
1
Even parity
1
0
1
Force parity to mark, HIGH
1
Forced parity to space, LOW
LCR[6]: Transmit Break Enable
When enabled, the Break control bit causes a break condition to be transmitted (the TX output is forced to a
“space’, logic 0, state). This condition remains, until disabled by setting LCR bit-6 to a logic 0.
Logic 0 = No TX break condition. (default)
Logic 1 = Forces the transmitter output (TX) to a “space”, logic 0, for alerting the remote receiver of a line
break condition.
LCR[7]: Baud Rate Divisors Enable
Baud rate generator divisor (DLL/DLM) enable.
Logic 0 = Data registers are selected (default).
Logic 1 = Divisor latch registers are selected.
4.7
Modem Control Register (MCR) or General Purpose Outputs Control - Read/Write
The MCR register is used for controlling the serial/modem interface signals or general purpose inputs/outputs.
MCR[0]: DTR# Output
The DTR# pin is a modem control output. If the modem interface is not used, this output may be used as a
general purpose output.
Logic 0 = Force DTR# output HIGH (default).
Logic 1 = Force DTR# output LOW.
MCR[1]: RTS# Output
The RTS# pin is a modem control output. If the modem interface is not used, this output may be used as a
general purpose output.
Logic 0 = Force RTS# output HIGH (default).
Logic 1 = Force RTS# output LOW.
MCR[2]: Reserved
OP1# is not available as an output pin on the V554. But it is available for use during Internal Loopback Mode.
In the Loopback Mode, this bit is used to write the state of the modem RI# interface signal.
相关PDF资料 |
PDF描述 |
|---|---|
| XR16V564IJ-F | IC UART FIFO 32B QUAD 68PLCC |
| XR16V598IQ100-F | IC UART FIFO 16B OCTAL 100QFP |
| XR16V654DIV-F | IC UART FIFO 64B QUAD 64LQFP |
| XR16V698IQ100-F | IC UART FIFO 32B OCTAL 100QFP |
| XR16V794IV-F | IC UART FIFO 64B QUAD 64LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR16V564 | 制造商:EXAR 制造商全称:EXAR 功能描述:2.25V TO 3.6V QUAD UART WITH 32-BYTE FIFO |
| XR16V564_07 | 制造商:EXAR 制造商全称:EXAR 功能描述:2.25V TO 3.6V QUAD UART WITH 32-BYTE FIFO |
| XR16V564D | 制造商:EXAR 制造商全称:EXAR 功能描述:2.25V TO 3.6V QUAD UART WITH 32-BYTE FIFO |
| XR16V564DIV | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
| XR16V564DIV-0A-EB | 功能描述:UART 接口集成电路 Supports V564 64 ld LQFP, ISA Interface RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。