- 您现在的位置：买卖IC网 > PDF目录16433 > XR16V598IQ-0A-EVB (Exar Corporation)EVAL BOARD FOR XR16V598-A 100QFP PDF资料下载
参数资料
| 型号： | XR16V598IQ-0A-EVB |
| 厂商： | Exar Corporation |
| 文件页数： | 10/58页 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD FOR XR16V598-A 100QFP |
| 标准包装： | 1 |
| 系列： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页
XR16V598
18
2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 16-BYTE FIFO
REV. 1.0.3
2.13
Auto RS-485 Half-duplex Control
The auto RS-485 half-duplex direction control changes the behavior of the transmitter when enabled by FCTR
bit-5. It also changes the behavior of the transmit empty interrupt (see Table 2). It asserts RTS# or DTR#
(LOW) after a specified delay indicated in MSR[7:4] following the last stop bit of the last character that has
been transmitted. This helps in turning around the transceiver to receive the remote station’s response. The
delay optimizes the time needed for the last transmission to reach the farthest station on a long cable network
before switching off the line driver. This delay prevents undesirable line signal disturbance that causes signal
degradation. When the host is ready to transmit next polling data packet again, it only has to load data bytes to
the transmit FIFO. The transmitter automatically de-asserts RTS# or DTR# output (HIGH) prior to sending the
data. The auto RS-485 half-duplex direction control also changes the transmitter empty interrupt to TSR empty
instead of THR empty.
2.13.1
Normal Multidrop Mode
Normal multidrop mode is enabled when MSR bit-0 = 1 and EFR bit-5 = 0 (Special Character Detect disabled).
The receiver is set to Force Parity 0 (LCR[5:3] = ’111’) in order to detect address bytes.
With the receiver initially disabled, it ignores all the data bytes (parity bit = 0) until an address byte is received
(parity bit = 1). This address byte will cause the UART to set the parity error. The UART will generate an LSR
interrupt and place the address byte in the RX FIFO. The software then examines the byte and enables the
receiver if the address matches its slave address, otherwise, it does not enable the receiver.
If the receiver has been enabled, the receiver will receive the subsequent data. If an address byte is received,
it will generate an LSR interrupt. The software again examines the byte and if the address matches its slave
address, it does not have to anything. If the address does not match its slave address, then the receiver
should be disabled.
2.13.2
Auto Address Detection
Auto address detection mode is enabled when MSR bit-0 = 1 and EFR bit-5 = 1. The desired slave address
will need to be written into the XOFF2 register. The receiver will try to detect an address byte that matches the
porgrammed character in the XOFF2 register. If the received byte is a data byte or an address byte that does
not match the programmed character in the XOFF2 register, the receiver will discard these data.
Upon
receiving an address byte that matches the XOFF2 character, the receiver will be automatically enabled if not
already enabled, and the address character is pushed into the RX FIFO along with the parity bit (in place of the
parity error bit). The receiver also generates an LSR interrupt. The receiver will then receive the subsequent
data. If another address byte is received and this address does not match the programmed XOFF2 character,
then the receiver will automatically be disabled and the address byte is ignored. If the address byte matches
XOFF2, the receiver will put this byte in the RX FIFO along with the parity bit in the parity error bit.
相关PDF资料 |
PDF描述 |
|---|---|
| APX809-46SRG-7 | IC MPU RESET CIRC 4.63V SOT23R-3 |
| 176819-000 | SOLDERSLEEVE LO-FIRE 11.5MM DIA |
| XR16M698IQ-0B-EVB | EVAL BOARD FOR M698-B 100QFP |
| XR16M698IQ-0A-EVB | EVAL BOARD FOR M698-A 100QFP |
| A3BBB-3018G | IDC CABLE- ASR30B/AE30G/ASR30B |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR16V598IQ-0B-EVB | 功能描述:界面开发工具 Supports V598 100 LD QFP, PCI Interface RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| XR16V598IQ100 | 制造商:EXAR 制造商全称:EXAR 功能描述:2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 16-BYTE FIFO |
| XR16V598IQ100-F | 功能描述:UART 接口集成电路 UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR16V654 | 制造商:EXAR 制造商全称:EXAR 功能描述:2.25V TO 3.6V QUAD UART WITH 64-BYTE FIFO |
| XR16V654_0709 | 制造商:EXAR 制造商全称:EXAR 功能描述:2.25V TO 3.6V QUAD UART WITH 64-BYTE FIFO |
发布紧急采购，3分钟左右您将得到回复。