- 您现在的位置：买卖IC网 > PDF目录16433 > XR16V598IQ-0A-EVB (Exar Corporation)EVAL BOARD FOR XR16V598-A 100QFP PDF资料下载
参数资料
| 型号： | XR16V598IQ-0A-EVB |
| 厂商： | Exar Corporation |
| 文件页数： | 9/58页 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD FOR XR16V598-A 100QFP |
| 标准包装： | 1 |
| 系列： | * |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页
XR16V598
17
REV. 1.0.3
2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 16-BYTE FIFO
(Xon1, Xon2, Xoff1, Xoff2) and controls TX transmissions accordingly. Under the above described flow control
mechanisms, flow control characters are not placed (stacked) in the user accessible RX data buffer or FIFO.
In the event that the receive buffer is overfilling and flow control needs to be executed, the 598 automatically
sends an Xoff message (when enabled) via the serial TX output to the remote modem. The 598 sends the Xoff-
1,2 characters two character times (= time taken to send two characters at the programmed baud rate) after
the receive FIFO crosses the programmed trigger level. To clear this condition, the 598 will transmit the
programmed Xon-1,2 characters as soon as receive FIFO is less than one trigger level below the programmed
trigger level. Table 6 below explains this.
* After the trigger level is reached, an xoff character is sent after a short span of time (= time required to send 2 characters);
for example, after 2.083ms has elapsed for 9600 baud and 10-bit word length setting.
2.12
Special Character Detect
A special character detect feature is provided to detect an 8-bit character when bit-5 is set in the Enhanced
Feature Register (EFR). When this character (Xoff2) is detected, it will be placed in the FIFO along with normal
incoming RX data. The 598 compares each incoming receive character with Xoff-2 data. If a match exists, the
received data will be transferred to FIFO and ISR bit-4 will be set to indicate detection of special character.
Although the Internal Register Table shows Xon, Xoff Registers with 8 bits of character information, the actual
number of bits is dependent on the programmed word length. Line Control Register (LCR) bits 0-1 defines the
number of character bits, i.e., either 5 bits, 6 bits, 7 bits, or 8 bits. The word length selected by LCR bits 0-1
also determines the number of bits that will be used for the special character comparison. Bit-0 in the Xon, Xoff
Registers corresponds to the LSB bit for the receive character.
TABLE 6: AUTO XON/XOFF (SOFTWARE) FLOW CONTROL
RX TRIGGER LEVEL
INT PIN ACTIVATION
XOFF CHARACTER(S) SENT
(CHARACTERS IN RX FIFO)
XON CHARACTER(S) SENT
(CHARACTERS IN RX FIFO)
1
1*
0
4
4*
1
8
8*
4
14
14*
8
相关PDF资料 |
PDF描述 |
|---|---|
| APX809-46SRG-7 | IC MPU RESET CIRC 4.63V SOT23R-3 |
| 176819-000 | SOLDERSLEEVE LO-FIRE 11.5MM DIA |
| XR16M698IQ-0B-EVB | EVAL BOARD FOR M698-B 100QFP |
| XR16M698IQ-0A-EVB | EVAL BOARD FOR M698-A 100QFP |
| A3BBB-3018G | IDC CABLE- ASR30B/AE30G/ASR30B |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR16V598IQ-0B-EVB | 功能描述:界面开发工具 Supports V598 100 LD QFP, PCI Interface RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| XR16V598IQ100 | 制造商:EXAR 制造商全称:EXAR 功能描述:2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 16-BYTE FIFO |
| XR16V598IQ100-F | 功能描述:UART 接口集成电路 UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR16V654 | 制造商:EXAR 制造商全称:EXAR 功能描述:2.25V TO 3.6V QUAD UART WITH 64-BYTE FIFO |
| XR16V654_0709 | 制造商:EXAR 制造商全称:EXAR 功能描述:2.25V TO 3.6V QUAD UART WITH 64-BYTE FIFO |
发布紧急采购，3分钟左右您将得到回复。