参数资料
| 型号： | XR68M752IL32-F |
| 厂商： | Exar Corporation |
| 文件页数： | 10/54页 |
| 文件大小： | 0K |
| 描述： | IC UART FIFO 64B DUAL 32QFN |
| 标准包装： | 490 |
| 特点： | * |
| 通道数： | 2，DUART |
| FIFO's： | 64 字节 |
| 规程： | RS232，RS422，RS485 |
| 电源电压： | 1.62 V ~ 3.63 V |
| 带自动流量控制功能： | 是 |
| 带IrDA 编码器/解码器： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN 裸露焊盘（5x5） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页
FIGURE 10. RECEIVER OPERATION IN FIFO AND AUTO RTS FLOW CONTROL MODE
Receive Data Shift
Register (RSR)
RXFIFO1
16X or 8X or 4X Clock
( DLD[5:4] )
Error
Ta
gs
(64
-s
et
s)
Err
or
Tag
sin
LS
R
b
its
4:
2
Receive Data Characters
FIFO
Trigger=16
Example
: - RX FIFO trigger level selected at 16 bytes
(See Note Below)
Data fills to
Halt Level
Data falls to
Resume Level
Data Bit
Validation
Receive
Data FIFO
Receive
Data
Receive Data
Byte and Errors
RHR Interrupt (ISR bit-2) programmed for
desired FIFO trigger level.
FIFO is Enabled by FCR bit-0=1
RTS# de-asserts when data fills to the Halt Level
to suspend remote transmitter.
Enable by EFR bit-6=1, MCR bit-1.
RTS# re-asserts when data falls to the Resume
Level to restart remote transmitter.
Enable by EFR bit-6=1, MCR bit-1.
64 bytes by 11-bit wide
FIFO
XR16M752/XR68M752
18
HIGH PERFORMANCE DUART WITH 64-BYTE FIFO
REV. 1.1.1
2.11
Auto RTS (Hardware) Flow Control
Automatic RTS hardware flow control is used to prevent data overrun to the local receiver FIFO. The RTS#
output is used to request remote unit to suspend/resume data transmission. The auto RTS flow control
features is enabled to fit specific application requirement (see Figure 11):
Enable auto RTS flow control using EFR bit-6.
The auto RTS function must be started by asserting RTS# output pin (MCR bit-1 to logic 1 after it is enabled).
If using the Auto RTS interrupt:
Enable RTS interrupt through IER bit-6 (after setting EFR bit-4). The UART issues an interrupt when the
RTS# pin makes a transition from low to high: ISR bit-5 will be set to logic 1.
2.12
Auto RTS Halt and Resume
The RTS# pin will not be forced HIGH (RTS off) until the receive FIFO reaches the Halt Level (TCR[3:0]). The
RTS# pin will return LOW after the RX FIFO is unloaded to the Resume Level (TCR[7:4]). Under these
conditions, the M752 will continue to accept data if the remote UART continues to transmit data. It is the
responsibility of the user to ensure that the Halt Level is greater than the Resume Level. If interrupts are used,
it is recommended that Halt Level > RX Trigger Level > Resume Level. The Auto RTS function is initiated
when the RTS# output pin is asserted LOW (RTS On).
2.13
Auto RS485 Half-duplex Control
The auto RS485 half-duplex direction control changes the behavior of the transmitter when enabled by DLD
bit-6. When idle, the auto RS485 half-duplex direction control signal (RTS#) is LOW for receive mode. When
data is loaded into the THR for transmission, the RTS# output is automatically asserted HIGH prior to sending
the data. After the last stop bit of the last character that has been transmitted, the RTS# signal is automatically
de-asserted. This helps in turning around the transceiver to receive the remote station’s response. When the
host is ready to transmit next polling data packet, it only has to load data bytes to the transmit FIFO. The
transmitter automatically re-asserts RTS# (HIGH) output prior to sending the data. In addition to changing the
behavior of the RTS# output, this feature also changes the behavior of the transmit empty interrupt (see
Table 4). In the 49-pin STBGA package, this feature can be enabled by connecting the EN485# pin to GND. If
this feature is enabled by the EN485# pin, it can be disabled by DLD bit-6 after power-up.
相关PDF资料 |
PDF描述 |
|---|---|
| XR16M752IL32-F | IC UART FIFO 64B DUAL 32QFN |
| ST16C1450IJ28-F | IC UART FIFO 1B 28PLCC |
| ST16C1450CQ48-F | IC UART FIFO 1B 48TQFP |
| ST16C450IJ44-F | IC UART SINGLE 44PLCC |
| XR16L2750CMTR-F | IC UART FIFO 64B DUAL 48TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR68M752IL32TR-F | 功能描述:UART 接口集成电路 W/64 BYTE FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR68M752IM-0B-EB | 功能描述:界面开发工具 Support XR68M752 48L TQFP, PCI Interface RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| XR68M752IM48 | 制造商:EXAR 制造商全称:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 64-BYTE FIFO |
| XR68M752IM48-F | 功能描述:UART 接口集成电路 UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR68M752IM48TR-F | 制造商:Exar Corporation 功能描述:XR68M752 Series 16 Mbps High Performance DUART With 64-Byte FIFO - TQFP-48 |
发布紧急采购，3分钟左右您将得到回复。