参数资料
| 型号： | XR68M752IL32-F |
| 厂商： | Exar Corporation |
| 文件页数： | 15/54页 |
| 文件大小： | 0K |
| 描述： | IC UART FIFO 64B DUAL 32QFN |
| 标准包装： | 490 |
| 特点： | * |
| 通道数： | 2，DUART |
| FIFO's： | 64 字节 |
| 规程： | RS232，RS422，RS485 |
| 电源电压： | 1.62 V ~ 3.63 V |
| 带自动流量控制功能： | 是 |
| 带IrDA 编码器/解码器： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN 裸露焊盘（5x5） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页
XR16M752/XR68M752
22
HIGH PERFORMANCE DUART WITH 64-BYTE FIFO
REV. 1.1.1
2.18
Sleep Mode with Wake-Up Indicator and PowerSave Feature
The M2751 supports low voltage system designs, hence, a sleep mode with auto wake-up and PowerSave
feature is included to reduce power consumption when the device is not actively used.
2.19
Sleep Mode with Auto Wake-Up
The M752 supports low voltage system designs, hence, a sleep mode is included to reduce its power
consumption when the chip is not actively used. In addition, there is a PowerSave Feature on the 49-pin
STBGA package that eliminates any unnecessary external buffer.
All of these conditions must be satisfied for the M752 to enter sleep mode:
■ no interrupts pending for both channels of the M752 (ISR bit-0 = 1)
■ sleep mode of both channels are enabled (IER bit-4 = 1)
■ modem inputs are not toggling (MSR bits 0-3 = 0)
■ RX input pins are idling HIGH
The M752 stops its crystal oscillator to conserve power in the sleep mode. User can check the XTAL2 pin for
no clock output as an indication that the device has entered the sleep mode.
The M752 resumes normal operation by any of the following:
■ a receive data start bit transition (HIGH to LOW)
■ a data byte is loaded to the transmitter, THR or FIFO
■ a change of logic state on any of the modem or general purpose serial inputs: CTS#, DSR#, CD#, RI#
If the M752 is awakened by any one of the above conditions, it will return to the sleep mode automatically after
all interrupting conditions have been serviced and cleared. If the M752 is awakened by the modem inputs, a
read to the MSR is required to reset the modem inputs. In any case, the sleep mode will not be entered while
an interrupt is pending from channel A or B. The M752 will stay in the sleep mode of operation until it is
disabled by setting IER bit-4 to a logic 0.
If the address lines, data bus lines, IOW#, IOR#, CSA#, CSB#, and modem input lines remain steady when the
M752 is in sleep mode, the maximum current will be in the microamp range as specified in the DC Electrical
Characteristics on page 40. If the input lines are floating or are toggling while the M752 is in sleep mode, the
current can be up to 100 times more. If any of those signals are toggling or floating, then an external buffer
would be required to keep the address, data and control lines steady to achieve the low current.
2.19.1
PowerSave Feature (49-pin STBGA pacakge only)
The PowerSave Feature will eliminate the need for an external buffer by internally isolating the address, data
and control signals from other bus activities that could cause wasteful power drain. The M752 enters
PowerSave mode when pin F1 is connected to VCC and the M752 is in sleep mode (see Sleep Mode section
above).
Since PowerSave mode isolates the address, data and control signals, the device will wake-up by:
■ a receive data start bit transition (HIGH to LOW)
■ a change of logic state on any of the modem or general purpose serial inputs: CTS#, DSR#, CD#, RI#
The M752 will return to the PowerSave mode automatically after a read to the MSR (to reset the modem
inputs) and all interrupting conditions have been serviced and cleared. The 2751 will stay in the PowerSave
mode of operation until it is disabled by setting IER bit-4 to a logic 0 and/or the PowerSave pin is connected to
GND.
A word of caution: owing to the starting up delay of the crystal oscillator after waking up from sleep mode, the
first few receive characters may be lost. The number of characters lost during the restart also depends on your
operating data rate. More characters are lost when operating at higher data rate. Also, it is important to keep
RX A/B inputs idling HIGH or “marking” condition during sleep mode to avoid receiving a “break” condition
upon the restart. This may occur when the external interface transceivers (RS-232, RS-485 or another type)
are also put to sleep mode and cannot maintain the “marking” condition. To avoid this, the designer can use a
47k-100k ohm pull-up resistor on the RXA and RXB pins.
相关PDF资料 |
PDF描述 |
|---|---|
| XR16M752IL32-F | IC UART FIFO 64B DUAL 32QFN |
| ST16C1450IJ28-F | IC UART FIFO 1B 28PLCC |
| ST16C1450CQ48-F | IC UART FIFO 1B 48TQFP |
| ST16C450IJ44-F | IC UART SINGLE 44PLCC |
| XR16L2750CMTR-F | IC UART FIFO 64B DUAL 48TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR68M752IL32TR-F | 功能描述:UART 接口集成电路 W/64 BYTE FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR68M752IM-0B-EB | 功能描述:界面开发工具 Support XR68M752 48L TQFP, PCI Interface RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| XR68M752IM48 | 制造商:EXAR 制造商全称:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 64-BYTE FIFO |
| XR68M752IM48-F | 功能描述:UART 接口集成电路 UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR68M752IM48TR-F | 制造商:Exar Corporation 功能描述:XR68M752 Series 16 Mbps High Performance DUART With 64-Byte FIFO - TQFP-48 |
发布紧急采购，3分钟左右您将得到回复。