参数资料
型号: XR88C681CP/40-F
厂商: Exar Corporation
文件页数: 37/101页
文件大小: 0K
描述: IC UART CMOS DUAL 40PDIP
标准包装: 9
特点: *
通道数: 2,DUART
FIFO's: 1 字节,3 字节
电源电压: 4.75 V ~ 5.25 V
带并行端口:
带CMOS:
安装类型: 通孔
封装/外壳: 40-DIP(0.600",15.24mm)
供应商设备封装: 40-PDIP
包装: 管件
其它名称: 1016-1328-5
XR88C681
40
Rev. 2.11
CPU
-INT
-IACK
-INTR
IEI
IEO
-IACK
-INTR
IEI
IEO
-IACK
-INTR
IEI
IEO
-IACK
-INTR
IEI
IEO
-IACK
VCC
HIGHEST
LOWEST
PRIORITY
Figure 15. A Diagram of Numerous DUARTs Configured in an Interrupt
Daisy Chain (for Z-Mode Operation)
VCC
In addition to the -INTR and -IACK pins, the Z-Mode
DUART also uses the IEI and IEO pins; which are defined
as follows:
IEI - Interrupt Enable Input
This active-high input is only available if the DUART is
configured to operate in the Z-Mode. If this input is at a
logic “high” then all unmasked interrupt requests, from
this DUART, are enabled.
Note:
Those interrupts which have been masked out by the IMR are
still disabled. However, if this input is at a logic “low”, then all
interrupts (whether masked or unmasked) are disabled.
Hence, IEI can act to globally disable all DUART interrupt
requests.
IEO - Interrupt Enable Output
This active-high output is only available if the DUART is
configured to operate in the Z-Mode. This output is often
times connected to the IEI input of another (lower priority)
device. This output is “high” if all of the following
conditions are true.
D
The device’s IEI input is at a logic “high”
D
The device is not requesting an interrupt from the
CPU
D
An interrupt, requested by the device, has just been
serviced
If any of these conditions are false, then the IEO pin will be
at a logic “low”.
Note
:
Once the IEO pin has toggled “low”, and the CPU has ac-
knowledged the interrupt request and has completed the inter-
rupt service routine, the IEO pin will remain “low” until the user
invokes the “RESET IUS” command (see Table 3). Therefore,
if the DUART is going to operate in the Z-Mode, the user must
include the “RESET IUS” Command at the very end of the
DUART interrupt service routine.
System Level Application of the IEI and IEO pins
Figure 15 depicts a series of DUARTs connected in a
daisy-chain fashion. In this figure, the left-most DUART
has the highest interrupt priority. This is because this
DUART’s IEI input is hardwired to Vcc. Therefore, the
unmasked interrupt requests, from this DUART are
always enabled. The DUART device, located just to the
right of the “highest interrupt priority” device is of a lower
interrupt priority. This is because the IEI input of this lower
priority device is connected to the IEO output of the
highest priority DUART. Whenever the “highest priority”
device requests an interrupt, its IEO output will toggle
“low”. This will in turn, disable the “lower priority” device
相关PDF资料
PDF描述
AT89C51RB2-RLRIM IC MCU FLASH 8051 16K 5V 44-VQFP
XR16V2550IM-F IC UART FIFO 16B 48TQFP
MAX7311AWG+T IC I/O EXPANDER I2C 16B 24SOIC
XR16L2750CM-F IC UART FIFO 64B DUAL 48TQFP
XR20M1172IL32-F IC UART FIFO I2C/SPI 64B 32QFN
相关代理商/技术参数
参数描述
XR88C681J 制造商:Exar Corporation 功能描述:
XR88C681J-F 功能描述:UART 接口集成电路 0.5V-2V UART temp -45 to 85C RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
XR88C681JTR-F 功能描述:UART 接口集成电路 Dual Channel UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
XR88C681MN-S0968 制造商:Exar Corporation 功能描述:
XR88C681N/40 制造商:EXAR 制造商全称:EXAR 功能描述:CMOS DUAL CHANNEL UART (DUART)