参数资料
型号: XRT75L04DIV-F
厂商: Exar Corporation
文件页数: 4/98页
文件大小: 0K
描述: IC LIU E3/DS3/STS-1 4CH 176TQFP
标准包装: 72
类型: 线路接口装置(LIU)
驱动器/接收器数: 4/4
规程: DS3,E3,STS-1
电源电压: 3.135 V ~ 3.465 V
安装类型: 表面贴装
封装/外壳: 176-LQFP
供应商设备封装: 176-TQFP(24x24)
包装: 托盘
XRT75L04D
á
FOUR CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
REV. 1.0.1
8
91
100
130
121
REQEN_0
REQEN_1
REQEN_2
REQEN_3
I
Receive Equalizer On/Off - Channel 0:
Receive Equalizer On/Off- Channel 1:
Receive Equalizer On/Off - Channel 2:
Receive Equalier On/Off- Channel 3:
Tie these pins “High” to enable the receive equalizer.
NOTES:
1.
This input pin is ignored and should be connected to GND if the
XRT75L04D is operating in the HOST Mode
2.
This pin is internally pulled down.
87
RxON/
SDI
I
Hardware Mode: Receiver Turn ON Input
Host Mode: Serial Data Input:
Function of this pin depends on whether the XRT75L04D is configured to oper-
ate in Hardware mode or Host mode.
In Hardware mode, setting this input pin “High” turns on and enables the
Receivers of all three channels.
NOTES:
1.
If the XRT75L04D is configured in HOST mode, this pin functions as
SDI input pin (please refer to the pin description for Microprocessor
Interface)
2.
This pin is internally pulled down.
86
RxClkINV/
CS
I
Hardware Mode: RxClk INVERT
Host Mode: Chip Select:
Function of this pin depends on whether the XRT75L04D is configured to oper-
ate in Hardware mode or Host mode.
In Hardware mode, setting this input pin “High” configures the Receiver Sec-
tion of all channels to invert the RxClk_n output signals and outputs the recov-
ered data via RPOS_n and RNEG_n on the falling edge of RxClk_n.
NOTE: If the XRT75L04D is configured in HOST mode, this pin functions as CS
input pin (please refer to the pin description for Microprocessor
Interface).
85
RxMON/
SDO
I
Hardware Mode: Receive Monitoring Mode
Host Mode: Serial Data Output:
In Hardware mode, when this pin is tied “High” all 4 channels configure into
monitoring channels. In the monitoring mode, the Receiver is capable of moni-
toring the signals with 20 dB flat loss plus 6 dB cable attenuation. This allows
monitoring very weak signal before declaring LOS.
In HOST Mode each channel can be independently configured to be a monitor-
ing channel by setting the bits in the channel control registers.
NOTE: If the XRT75L04D is configured in HOST mode, this pin functions as
SDO pin (please refer to the pin description for the Microprocessor
Interface).
RECEIVE INTERFACE
PIN #
SIGNAL NAME
TYPE
DESCRIPTION
相关PDF资料
PDF描述
XRT75L04IV-F IC LIU E3/DS3/STS-1 4CH 176LQFP
XRT75L06DIB-F IC LIU E3/DS3/STS-1 6CH 217BGA
XRT75L06IB-F IC LIU E3/DS3/STS-1 6CH 217BGA
XRT75R03DIV-F IC LIU E3/DS3/STS-1 3CH 128LQFP
XRT75R03IV-F IC LIU E3/DS3/STS-1 3CH 128LQFP
相关代理商/技术参数
参数描述
XRT75L04DIVTR 功能描述:时钟合成器/抖动清除器 4 CHNL E3/DS3/STS 1 JITTER ATTENUATOR RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel
XRT75L04DIVTR-F 功能描述:时钟合成器/抖动清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel
XRT75L04ES 功能描述:时钟合成器/抖动清除器 4CH T3/E3/STS1 LIU+JA 3.3V RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel
XRT75L04IV 功能描述:外围驱动器与原件 - PCI 4CH E3/DS3/STS1 JITTER ATTENUATOR RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray
XRT75L04IV-F 功能描述:外围驱动器与原件 - PCI 4-Ch DS3, E3, STS-1 RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray