参数资料
型号: XRT75L04IV
厂商: Exar Corporation
文件页数: 3/57页
文件大小: 0K
描述: IC LIU E3/DS3/STS-1 4CH 176LQFP
标准包装: 72
类型: 线路接口装置(LIU)
驱动器/接收器数: 4/4
规程: DS3,E3,STS-1
电源电压: 3.135 V ~ 3.465 V
安装类型: 表面贴装
封装/外壳: 176-LQFP
供应商设备封装: 176-TQFP(24x24)
包装: 托盘
XRT75L04
9
REV. 1.0.4
FOUR CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
CLOCK INTERFACE
PIN #
SIGNAL NAME
TYPE
DESCRIPTION
69
E3CLK
I
E3 Clock Input (34.368 MHz ± 20 ppm):
If any of the channels is configured in E3 mode, a reference clock 34.368 MHz
is applied on this pin.
NOTE: In single frequency mode, this reference clock is not required.
67
DS3CLK
I
DS3 Clock Input (44.736 MHz ± 20 ppm):
If any of the channels is configured in DS3 mode, a reference clock 44.736
MHz. is applied on this pin.
NOTE: In single frequency mode, this reference clock is not required.
65
STS-1CLK/ 12M
I
STS-1 Clock Input (51.84 MHz ± 20 ppm):
If any of the channels is configured in STS-1 mode, a reference clock 51.84
MHz is applied on this pin..
In Single Frequency Mode, a reference clock of 12.288 MHz ± 20 ppm is con-
nected to this pin and the internal clock synthesizer generates the appropriate
clock frequencies based on the configuration of the channels in E3, DS3 or
STS-1.
156
SFM_EN
I
Single Frequency Mode Enable:
Tie this pin “High” to enable the Single Frequency Mode. A reference clock of
12.288 MHz ± 20 ppm is applied. This offers the flexibility of using a low cost
reference clock and configures the board for either E3 or DS3 or STS-1 without
the need to change any components on the board.
In the Single Frequency Mode (SFM) an output clock is provided for each chan-
nel if the CLK_EN bit is set thus eliminating the need for a separate clock
source for the framer.
Tie this pin “Low” if single frequency mode is not selected. In this case, the
appropriate reference clocks must be provided.
NOTE:
This pin is internally pulled down
57
54
164
167
CLKOUTEN_0
CLKOUTEN_1
CLKOUTEN_2
CLKOUTEN_3
O
Clock output enable for channel 0
Clock output enable for channel 1
Clock output enable for channel 2
Clock output enable for channel 3
Pull this pin “High” to output low jitter clock on the CLKOUT_n pins.
NOTES:
1.
This clock output is only available in SFM mode.
2.
The maximum drive capability for the clockouts is 16 mA.
60
63
161
158
CLKOUT_0
CLKOUT_1
CLKOUT_2
CLKOUT_3
O
Clock output for channel 0
Clock output for channel 1
Clock output for channel 2
Clock output for channel 3
If CLKOUTEN_n pin is “High”, low jitter clock is output for each channel. Fre-
quency of these clocks is based on the mode (E3,DS3 or STS-1) the channels
are configured.
This eliminates the need for a separate clock source for the framer.
NOTES:
1.
This clock output is only available in SFM mode.
2.
The maximum drive capability for the clockouts is 16 mA.
相关PDF资料
PDF描述
VI-23W-MY CONVERTER MOD DC/DC 5.5V 50W
XRT75L03DIVTR-F IC LIU E3/DS3/STS-1 3CH 128LQFP
IDT72835LB15PF IC FIFO SYNC DL 2048X18 128TQFP
XRT75L06IB IC LIU E3/DS3/STS-1 6CH 217BGA
ISL26132AVZ-T IC ADC 24BIT SRL 80SPS 24TSSOP
相关代理商/技术参数
参数描述
XRT75L04IV-F 功能描述:外围驱动器与原件 - PCI 4-Ch DS3, E3, STS-1 RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray
XRT75L04IVTR 功能描述:时钟合成器/抖动清除器 4CH E3/DS3/STS1 JITTER ATTENUATOR RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel
XRT75L04IVTR-F 功能描述:时钟合成器/抖动清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel
XRT75L06 制造商:EXAR 制造商全称:EXAR 功能描述:SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
XRT75L06D 制造商:EXAR 制造商全称:EXAR 功能描述:SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER