参数资料
| 型号： | XRT75L04IV |
| 厂商： | Exar Corporation |
| 文件页数： | 4/57页 |
| 文件大小： | 0K |
| 描述： | IC LIU E3/DS3/STS-1 4CH 176LQFP |
| 标准包装： | 72 |
| 类型： | 线路接口装置（LIU） |
| 驱动器/接收器数： | 4/4 |
| 规程： | DS3，E3，STS-1 |
| 电源电压： | 3.135 V ~ 3.465 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 176-LQFP |
| 供应商设备封装： | 176-TQFP（24x24） |
| 包装： | 托盘 |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页
XRT75L04
10
FOUR CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
REV. 1.0.4
CONTROL AND ALARM INTERFACE
PIN #
SIGNAL NAME
TYPE
DESCRIPTION
36
24
9
21
MRING_0
MRING_1
MRING_2
MRING_3
I
Monitor Ring Input - Channel 0:
Monitor Ring Input - Channel 1:
Monitor Ring Input - Channel 2:
Monitor Ring Input - Channel 3:
The bipolar line output signal from TRING_n is connected to this pin via a 270
resistor to check for line driver failure.
NOTE: This pin is internally pulled "Low".
37
25
8
20
MTIP_0
MTIP_1
MTIP_2
MTIP_3
I
Monitor Tip Input - Channel 0:
Monitor Tip Input - Channel 1:
Monitor Tip Input - Channel 2:
Monitor Tip Input - Channel 3:
The bipolar line output signal from TTIP_n is connected to this pin via a 270-
ohm resistor to check for line driver failure.
NOTE: This pin is internally pulled "Low".
42
30
3
15
DMO_0
DMO_1
DMO_2
DMO_3
O
Drive Monitor Output - Channel 0:
Drive Monitor Output - Channel 1:
Drive Monitor Output - Channel 2:
Drive Monitor Output - Channel 3:
If MTIP_n and MRING_n has no transition pulse for 128 ± 32 TxCLK_n cycles,
DMO_n goes “High” to indicate the driver failure. DMO_n output stays “High”
until the next AMI signal is detected.
83
76
138
145
RLOS_0
RLOS_1
RLOS_2
RLOS_3
O
Receive Loss of Signal Output Indicator - Channel 0:
Receive Loss of Signal Output Indicator - Channel 1:
Receive Loss of Signal Output Indicator - Channel 2:
Receive Loss of Signal Output Indicator - Channel 3:
This output pin toggles "High" if the receiver has detected a Loss of Signal Con-
dition.
The criteria for declaring /clearing an LOS Condition depends upon whether it is
operating in the E3 or STS-1/DS3 Mode.
82
75
139
146
RLOL_0
RLOL_1
RLOL_2
RLOL_3
O
Receive Loss of Lock Output Indicator - Channel 0:
Receive Loss of Lock Output Indicator - Channel 1:
Receive Loss of Lock Output Indicator - Channel 2:
Receive Loss of Lock Output Indicator - Channel 3:
This output pin toggles "High" if a Loss of Lock Condition is detected. LOL
(Loss of Lock) condition occurs if the recovered clock frequency deviates from
the Reference Clock frequency (available at either E3CLK or DS3CLK or STS-
1CLK input pins) by more than 0.5%.
111
RXA
****
External Resistor of 3 K
± 1%.
Should be connected between RxA and RxB for internal bias.
110
RXB
****
External Resistor of 3K
±1%.
Should be connected between RxA and RxB for internal bias.
相关PDF资料 |
PDF描述 |
|---|---|
| VI-23W-MY | CONVERTER MOD DC/DC 5.5V 50W |
| XRT75L03DIVTR-F | IC LIU E3/DS3/STS-1 3CH 128LQFP |
| IDT72835LB15PF | IC FIFO SYNC DL 2048X18 128TQFP |
| XRT75L06IB | IC LIU E3/DS3/STS-1 6CH 217BGA |
| ISL26132AVZ-T | IC ADC 24BIT SRL 80SPS 24TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XRT75L04IV-F | 功能描述:外围驱动器与原件 - PCI 4-Ch DS3, E3, STS-1 RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| XRT75L04IVTR | 功能描述:时钟合成器/抖动清除器 4CH E3/DS3/STS1 JITTER ATTENUATOR RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel |
| XRT75L04IVTR-F | 功能描述:时钟合成器/抖动清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel |
| XRT75L06 | 制造商:EXAR 制造商全称:EXAR 功能描述:SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR |
| XRT75L06D | 制造商:EXAR 制造商全称:EXAR 功能描述:SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER |
发布紧急采购，3分钟左右您将得到回复。