参数资料
型号: XRT75L06DIB-F
厂商: Exar Corporation
文件页数: 85/103页
文件大小: 0K
描述: IC LIU E3/DS3/STS-1 6CH 217BGA
标准包装: 60
类型: 线路接口装置(LIU)
驱动器/接收器数: 6/6
规程: DS3,E3,STS-1
电源电压: 3.135 V ~ 3.465 V
安装类型: 表面贴装
封装/外壳: 217-BBGA
供应商设备封装: 217-BGA(23x23)
包装: 托盘
xr
XRT75L06D
REV. 1.0.4
SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
78
NOTE: All of these intrinsic jitter measurements are to be performed using a band-pass filter of 10Hz to 400kHz.
Each of the scenarios presented in Table 19, are briefly described below.
7.5.1
DS3 De-Mapping Jitter
DS3 De-Mapping Jitter is the amount of Intrinsic Jitter that will be measured within the "Line" or "Facility-side"
DS3 signal, (after it has been de-mapped from a SONET signal) without the occurrence of "Pointer
Adjustments" within the SONET signal.
Telcordia GR-253-CORE requires that the "DS3 De-Mapping" Jitter be less than 0.4UI-pp, when measured
over all possible combinations of DS3 and STS-1 frequency offsets.
7.5.2
Single Pointer Adjustment
Telcordia GR-253-CORE states that if each pointer adjustment (within a continuous stream of pointer
adjustments) is separated from each other by a period of 30 seconds, or more; then they are sufficiently
isolated to be considered "Single-Pointer Adjustments".
Figure 56 presents an illustration of the "Single Pointer Adjustment" Scenario.
Telcordia GR-253-CORE states that the Intrinsic Jitter that is measured (within the DS3 signal) that is
ultimately de-mapped from a SONET signal that is experiencing "Single-Pointer Adjustment" events, must
NOT exceed the value 0.3UI-pp + Ao.
NOTES:
1.
Ao is the amount of Intrinsic Jitter that was measured during the "De-Mapping" Jitter portion of this test.
2.
Testing must be performed for both Incrementing and Decrementing Pointer Adjustments.
7.5.3
Pointer Burst
Figure 57 presents an illustration of the "Pointer Burst" Pointer Adjustment Scenario per Telcordia GR-253-
CORE.
Continuous Add
A5
1.3UI-pp
Includes effects of Jitter from Clock-Gapping, De-Map-
ping and Pointer Adjustments.
Continuous Cancel
A5
1.3UI-pp
Includes effects of Jitter from Clock-Gapping, De-Map-
ping and Pointer Adjustments.
FIGURE 56. ILLUSTRATION OF SINGLE POINTER ADJUSTMENT SCENARIO
TABLE 19: SUMMARY OF "CATEGORY I INTRINSIC JITTER REQUIREMENT PER TELCORDIA GR-253-CORE, FOR DS3
APPLICATIONS
SCENARIO
DESCRIPTION
SCENARIO
NUMBER
TELCORDIA GR-253-CORE
CATEGORY I INTRINSIC
JITTER REQUIREMENTS
COMMENTS
Initialization
Cool Down
Measurement Period
>30s
Pointer Adjustment Events
相关PDF资料
PDF描述
XRT75L06IB-F IC LIU E3/DS3/STS-1 6CH 217BGA
XRT75R03DIV-F IC LIU E3/DS3/STS-1 3CH 128LQFP
XRT75R03IV-F IC LIU E3/DS3/STS-1 3CH 128LQFP
XRT75R06DIB-F IC LIU E3/DS3/STS-1 6CH 217BGA
XRT75R06IB-F IC LIU E3/DS3/STS-1 6CH 217BGA
相关代理商/技术参数
参数描述
XRT75L06ES 功能描述:时钟合成器/抖动清除器 6 CHT3/E3/STS1 LIU+JA 3.3V RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel
XRT75L06IB 功能描述:接口 - 专用 6CH E3/DS3/STS1 LIU+Jitter Attenuato RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59
XRT75L06IB-F 功能描述:外围驱动器与原件 - PCI 6-Ch DS3, E3, STS-1 RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray
XRT75R03 制造商:EXAR 制造商全称:EXAR 功能描述:THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
XRT75R03D 制造商:EXAR 制造商全称:EXAR 功能描述:THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCRONIZER