参数资料
| 型号： | XRT75L06IB-F |
| 厂商： | Exar Corporation |
| 文件页数： | 41/63页 |
| 文件大小： | 0K |
| 描述： | IC LIU E3/DS3/STS-1 6CH 217BGA |
| 标准包装： | 60 |
| 类型： | 线路接口装置（LIU） |
| 驱动器/接收器数： | 6/6 |
| 规程： | DS3，E3，STS-1 |
| 电源电压： | 3.135 V ~ 3.465 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 217-BBGA |
| 供应商设备封装： | 217-BGA（23x23） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页当前第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页
XRT75L06
REV. 1.0.3
SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
43
6.1
THE MICROPROCESSOR INTERFACE BLOCK SIGNALS
The LIU may be configured into different operating modes and have its performance monitored by software
through a standard microprocessor using data, address and control signals. These interface signals are de-
scribed below in Table 12. The microprocessor interface can be configured to operate in Asynchronous mode
or Synchronous mode.
TABLE 12: XRT75L06 MICROPROCESSOR INTERFACE SIGNALS
PIN NAME
TYPE
DESCRIPTION
Pmode
I
Microprocessor Interface Mode Select Input pin
This pin is used to specify the microprocessor interface mode.
D[7:0]
I/O
Bi-Directional Data Bus for register "Read" or "Write" Operations.
Addr[7:0]
I
Eight-Bit Address Bus Inputs
The XRT75L06 LIU microprocessor interface uses a direct address bus. This address bus is
provided to permit the user to select an on-chip register for Read/Write access.
CS
I
Chip Select Input
This active low signal selects the microprocessor interface of the XRT75L06 LIU and enables
Read/Write operations with the on-chip register locations.
RD
I
Read Signal This active low input functions as the read signal from the local
P. When this
pin is pulled “Low” (if CS is “Low”) the LIU is informed that a read operation has been
requested and begins the process of the read cycle.
WR
I
Write Signal This active low input functions as the write signal from the local
P. When this
pin is pulled “Low” (if CS is “Low”) the LIU is informed that a write operation has been
requested and begins the process of the write cycle.
RDY
O
Ready Output This active low signal is provided by the LIU device. It indicates that the cur-
rent read or write cycle is complete, and the LIU is waiting for the next command.
INT
O
Interrupt Output This active low signal is provided by the LIU to alert the local mP that a
change in alarm status has occured. This pin is Reset Upon Read (RUR) once the alarm sta-
tus registers have been cleared.
RESET
I
Reset Input This active low input pin is used to Reset the LIU.
相关PDF资料 |
PDF描述 |
|---|---|
| XRT75R03DIV-F | IC LIU E3/DS3/STS-1 3CH 128LQFP |
| XRT75R03IV-F | IC LIU E3/DS3/STS-1 3CH 128LQFP |
| XRT75R06DIB-F | IC LIU E3/DS3/STS-1 6CH 217BGA |
| XRT75R06IB-F | IC LIU E3/DS3/STS-1 6CH 217BGA |
| XRT75R12DIB-L | IC LIU E3/DS3/STS-1 12CH 420TBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XRT75R03 | 制造商:EXAR 制造商全称:EXAR 功能描述:THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR |
| XRT75R03D | 制造商:EXAR 制造商全称:EXAR 功能描述:THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCRONIZER |
| XRT75R03D_06 | 制造商:EXAR 制造商全称:EXAR 功能描述:EXAR DATA SHEET FORMAT TEMPLATES |
| XRT75R03DES | 功能描述:时钟合成器/抖动清除器 3CH T3/E3/STS1LIU+D 3.3V W/REDUNDANCY RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel |
| XRT75R03DIV | 功能描述:时钟合成器/抖动清除器 3CHNNEL E3/DS3/STS 1 JITTER ATTENUATOR RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。