参数资料
型号: XRT75R12DIB
厂商: Exar Corporation
文件页数: 80/133页
文件大小: 0K
描述: IC LIU E3/DS3/STS-1 12CH 420TBGA
标准包装: 40
类型: 线路接口装置(LIU)
驱动器/接收器数: 12/12
规程: DS3,E3,STS-1
电源电压: 3.135 V ~ 3.465 V
安装类型: 表面贴装
封装/外壳: 420-LBGA 裸露焊盘
供应商设备封装: 420-TBGA(35x35)
包装: 托盘
XRT75R12D
46
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
REV. 1.0.3
7.1
THE MICROPROCESSOR INTERFACE BLOCK SIGNALS
The LIU may be configured into different operating modes and have its performance monitored by software
through a standard microprocessor using data, address and control signals. These interface signals are de-
scribed below in Table 14. The microprocessor interface can be configured to operate in Asynchronous mode
or Synchronous mode.
TABLE 14: XRT75R12D MICROPROCESSOR INTERFACE SIGNALS
PIN NAME
TYPE
DESCRIPTION
Pmode
I
Microprocessor Interface Mode Select Input pin
This pin is used to specify the microprocessor interface mode.
D[7:0]
I/O
Bi-Directional Data Bus for register "Read" or "Write" Operations.
Addr[7:0]
I
Eight-Bit Address Bus Inputs
The XRT75R12D LIU microprocessor interface uses a direct address bus. This address bus is
provided to permit the user to select an on-chip register for Read/Write access.
CS
I
Chip Select Input
This active low signal selects the microprocessor interface of the XRT75R12D LIU and
enables Read/Write operations with the on-chip register locations.
RD
I
Read Signal This active low input functions as the read signal from the local
P. When this
pin is pulled “Low” (if CS is “Low”) the LIU is informed that a read operation has been
requested and begins the process of the read cycle.
WR
I
Write Signal This active low input functions as the write signal from the local
P. When this
pin is pulled “Low” (if CS is “Low”) the LIU is informed that a write operation has been
requested and begins the process of the write cycle.
RDY
O
Ready Output This active low signal is provided by the LIU device. It indicates that the cur-
rent read or write cycle is complete, and the LIU is waiting for the next command.
INT
O
Interrupt Output This active low signal is provided by the LIU to alert the local mP that a
change in alarm status has occured. This pin is Reset Upon Read (RUR) once the alarm sta-
tus registers have been cleared.
RESET
I
Reset Input This active low input pin is used to Reset the LIU.
相关PDF资料
PDF描述
XRT75R12IB IC LIU E3/DS3/STS-1 12CH 420TBGA
ISL267450AIUZ-T IC INTERFACE
MS3116P16-8P CONN PLUG 8POS STRAIGHT W/PINS
IDT72V815L15PFI IC FIFO SYNC 512X18 15NS 128QFP
MS27513E8F35SD CONN RCPT 6POS BOX MNT W/SCKT
相关代理商/技术参数
参数描述
XRT75R12DIB-F 功能描述:网络控制器与处理器 IC 12 Channel 3.3V-5V temp -45 to 85C RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
XRT75R12DIB-L 功能描述:LIN 收发器 Synch RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8
XRT75R12ES 功能描述:时钟合成器/抖动清除器 12CH T3/E3/STS1LIUJA 3.3V W/REDUNDANCY RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel
XRT75R12IB 功能描述:外围驱动器与原件 - PCI 12CH E3/DS3/STS W/JITTER R3 TECH RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray
XRT75R12IB-F 功能描述:外围驱动器与原件 - PCI 12 Channel 3.3V-5V temp -45 to 85C RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray